background image

 
 

Model: NCMO-5G4W10C0 MANUAL

 

 

 

 

 

 

 

                                             NCM Supplies Inc. 

                             8125 NW 64

th

 ST. Miami, Florida 33166 

                           Phone: 305-640-0461 Fax: 305-639-2684 

                  [email protected] 

www.ncmsupplies.com

 

Unless otherwise noted, the above specifications reflect typical device performance at stated reference levels in the recommended operating configuration(s). 
Specifications are subject to change without notice. 
 
NCMO-5G4W10C0 MANUAL (1.1Rev2020) © 2000-2020 NCM Supplies 

 All Rights Reserved 

 

Chapter2: Installation 

2.1Equipment Installation                                                                  
ONU product is a fixed configuration cassette equipment. Site equipment installation is relatively simple. Simply install the 
device on a specified place, connecting the upstream fiber subscriber line connections, connect the power cable. Actual 
operation is as follows: 
2.1.1 Installed on the desktop 
Place the machine on a clean bench, this installation is relatively simple, you can observe the following operation: 

• Ensure the smooth 

workbench. 

• Around the device enough space for heat dissipation.

 

• Do not place objects on the device.

 

2.2.2. Mounted on the wall 

• Observation ONU equipment chassis two cruciform recess, in accordance with the position of the groove, instead two screws 

in the wall 

• The original selected two mounting screws gently snap into recesses aligned.

 

• Slowly let go, so that the device under the support of the screw hanging on the wall.

 

 
2.2 Installation Requirements 
To avoid equipment damage caused by improper use and personal injury, please observe 
the following precautions: 

• Do not place the device near water or in damp places, in order to prevent water or moisture from entering the device.

 

• Do not put the device in an unstable place, avoid falling 

damage to equipment. 

• Make sure that the supply voltage of the device matches the required voltage value.

 

• Do not open the equipment chassis without permission.

 

• Unplug before cleaning the power plug; prohibit the use of liquid cleaning.

 

 
2.3 Environment requirements 
ONU equipment must be installed in the interior, and to ensure the following conditions: 

• Confirmation at the ONU installation with enough space to facilitate cooling machine.

 

• ONU suitable operating temperature of 0°C —

 50°C, humidity 10% to 90%. 

Electromagnetic Environment 
ONU equipment in use can be affected by external electromagnetic interferences, such as 
radiation and conduction through the impact on the device, this should note the following: 

• Device workplace should avoid 

radio transmitters, radar stations, and high-frequency interface from power equipment. 

• User cable typically require alignment indoors if outdoor lighting traces measures should.

 

2.4 Cable Connection 
Optional cable connection for different model 
Rear View for multiple port 

 

 

 

Содержание NCMO-5G4W10C0










Отзывы: