background image

 

 

2.

 

DEVICE

 

CONNECTION 

 

2.1 Installation 

 
Before the system installation, first of all, it is necessary to determine the type and number of the connecting 

sensors, the identification system and other additional equipment. It is also necessary to be sure that all the additional 

equipment connected to the terminal are operable. 

Immediately  before  installing  the  system  and  connecting  the  equipment,  also  make  sure  that  the  cellular 

operator provides good communication quality in the intended location of the GSM antenna. 

The navigation antenna should  be installed  in such a way as to ensure maximum  "visibility" of navigation 

satellites in the upper hemisphere. 

 

Attention! 

In order to avoid overheating of the device and failure of the Li-Po battery, it is prohibited to install the tracker 

in  places  with  an  ambient  temperature  more  than  +60  °  C,  for  example,  near  heating  systems,  etc.  It  is  also 

prohibited to place the device in a sealed container without heat dissipation. 

It is prohibited to install tracker in places with high humidity and in places where there is a risk of possible 

ingress of liquid or large amount of dust into the case. 

 

When the device is connected to the Microfit-14 connectors harnesses, the connectors themselves should not 

be connected to the device. Each pin of this connector has a numeric code. The purpose of each is shown in Figure 
16 

At the stage of checking the correctness of the connection and settings of the device, it is not recommended 

to directly include actuating devices in the output circuits. It is advisable to do this at the final stage of verification. 

The power supply of digital and analogue fuel sensors must be connected through the fuses supplied with the 

sensors directly to the power supply. 

The power supply “-” (“ground”) of all connected external sensors must be combined with the power supply 

“-” (contact “G”) of the device. 

The interface lines of fuel sensors should be connected directly to the device without additional elements. 

Switches must be made with the power off. 

Connection to the car CAN bus should be carried out with the car ignition off. 
 

 

2.2 SIM-card installation and operation 

 

The  device  supports using of two SIM-cards. The first SIM  card  (external) is the main by default, and its 

installation is carried out without the use of special tools. For installation of the second  SIM-card (internal), it is 

necessary to remove the back panel of the device using a screwdriver. 

After turning-on or rebooting, the device starts operation with the main SIM - card. In the settings, either an 

external or internal SIM card can be selected as the main one. 

Switching  to  the  second  SIM-card  occurs  when  registration  on  the  first  SIM-card  is  lost  and  there  is  no 

registration after the next GSM modem rebooting. Also switching to the second SIM-card occurs after a series of 

unsuccessful attempts to connect to the telematics server.  When operating  on a secondary SIM-card,  a periodic 
availability check can be performed. 

 

 

 

Figure 22. SIM-card installation to the device 

Содержание SIGNAL S-2654





































Отзывы: