background image

TRACKER 5505/5505i/5605 Installation and Operation Manual

17

NAVMAN 

Preparing

A route is a list of waypoints that the boat can 
follow (see section 6).

 

To create waypoints before creating the 
route, see section 5-2-1.

 

To create a route, see section 6-2-1.

Starting a route from the chart display:

1  Go to the chart display.
2.  Press                  and select 

Start Route.

3.  Press        or        to highlight the route to 

follow. Press              .

4.  The TRACKER asks for the direction to 

traverse the route.

      Select 

Forward

 (the order the route was 

created) or 

Reverse

.

5.  The TRACKER displays the chart with the  
 

route marked and starts navigating from  

 

the start of the route.

Starting a route from the routes display:

1  Go to the routes display.
2  Press 

 or 

 to highlight the route to 

follow. Press 

 and select 

Start.

3  The TRACKER asks for the direction to 

traverse the route.

 

Select 

Forward

 (the order the route was 

created) or 

Reverse.

3-1-3 Following a route

4  The TRACKER displays a chart with the 

route marked and starts navigating from 
the start of the route.

Navigating

The TRACKER navigates to each waypoint on 
the route in turn as described in section 3-1-1.
The TRACKER stops navigating to the waypoint 
at the end of the current leg and starts the next 
leg of the route:
a  when the boat comes within 0.025 nm of 

the waypoint

b  or when the boat passes the waypoint
c  or if you skip the waypoint.

Skipping a waypoint

To skip a waypoint, go to a chart display, press 

 and select 

Skip

. The TRACKER starts 

navigating straight towards the next waypoint 
on the route.

Cancelling a route

When the boat has reached the final waypoint, 
or to stop the boat following the route at any 
time, cancel the route. Go to a chart display, 
press 

 and select 

Cancel route. 

 Tip:

 Before starting, create waypoints at points of interest. Create a waypoint at the start of the 

trip for you to navigate back to (see section 5-2-1).

Going to a point on the chart

1  Switch to a chart display.
2  Move the cursor to the destination point: 

either use the cursor keys or use Find (see 
section 3-2-5).

3  Press 

 and select 

Goto cursor.

Navigating

The TRACKER navigates to the point as 
described in section 3-1-1.

Cancelling navigating

Go to a Chart display, press 

 and select 

Cancel goto.

CAUTION

!

!

CAUTION

DANGER

WARNING

Make sure the course does not pass over 
land or dangerous waters.

CAUTION

!

!

CAUTION

DANGER

WARNING

Skipping a waypoint with the autopilot on 
might result in a sudden course change.

www.Busse-Yachtshop.de      email: [email protected]

Содержание Tracker 5505





































































Отзывы: