background image

4

LA010065D

 

© 2004 Navman NZ Ltd. All rights reserved. Proprietary information and specifications subject to change without notice.

Features

New features

• power management control

• 3.3–5 V operation (autosensing)

• superior dead-reckoning (DR) capability in absence of GPS signals (DR model only)

• reliable single-chip RF containing: Fractional-N synthesiser, VCO, LNA

Continuing the Jupiter legacy:

• 12 parallel satellite tracking channels for fast acquisition and re-acquisition

• Fast Time-To-First-Fix (TTFF) 

—24 second hot start

—42 seconds warm start

—Less than 2 second re-acquisition after blockages for up to 10 seconds 

• enhanced algorithms for superior navigation performance in dense urban areas and foliage 

environments

• adaptive threshold-based signal detection for improved reception of weak signals

• maximum navigation accuracy using Standard Positioning Service (SPS)

• automatic altitude hold mode from 3D to 2D navigation

• automatic cold start acquisition process (no initialisation data entered) 

• flexible and configurable operation via user commands over host serial port

• position and velocity initialisation via the host serial port

• user selectable satellites

• user-specifiable visible satellite mask angle

• serial data output including Navman binary protocol and selected National Marine Electronics 

Association (NMEA-0183) v2.1 messages

Содержание Jupiter 12



















Отзывы: