manualshive.com logo in svg
background image

25

Warranty

 

Subjecting the heat exchanger to pressures or 

firing rates greater or lesser than those shown on 

the rating plate or removal of or alteration to the 

rating plate.

 

Installation at any location outside the United 

States or Canada.

 

Improper conversion from natural gas to liquid 

propane gas or liquid propane gas to natural 

gas or attempt to operate with a type of gas not 

specified for the boiler.

 

Accidental or intentional damage.

There is no warranty on any Product purchased 

through the internet or from any installer that 

obtained the Product from a supplier or distributor 

not authorized by Navien.

Warranty Limitations

EXCEPT AS EXPRESSLY PROVIDED HEREIN, THERE 

ARE NO OTHER WARRANTIES, EXPRESSED OR 

IMPLIED, INCLUDING, BUT NOT LIMITED TO 

WARRANTIES OR MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE, WHICH EXTEND 

BEYOND THE DESCRIPTION OF THE WARRANTY 

HEREIN AND FURTHER NAVIEN SHALL NOT BE 

LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL, 

CONSEQUENTIAL, PUNITIVE OR OTHER SIMILAR 

DAMAGES THAT MAY ARISE, INCLUDING LOST 

PROFITS, DAMAGE TO A PERSON OR PROPERTY, 

LOSS OF USE, INCONVENIENCE, OR LIABILITY 

ARISING FROM IMPROPER INSTALLATION, 

SERVICE OR USE OF THE PRODUCT. ANY IMPLIED 

WARRANTIES OF MERCHANTABILITY AND FITNESS 

ARISING UNDER STATE LAW ARE LIMITED IN 

DURATION TO THE PERIOD OF COVERAGE PROVIDED 

BY THIS WARRANTY, UNLESS THE PERIOD PROVIDED 

BY STATE LAW IS LESS.

No one is authorized to make any other warranties 

on behalf of Navien. Some states do not allow the 

exclusion or limitation of incidental or consequential 

damages, or how long an implied warranty lasts, so 

the above limitation may not apply to you.

This Limited Warranty gives you specific legal rights 

and you may also have other rights which vary from 

state to state.

Proof of the date of installation must be provided to 

Navien. At Navien’s request, the defective Product 

or part must be returned to Navien. When the 

Product is installed in new construction, the date 

of installation shall be established as the date upon 

which the end-user takes title to the real property. If 

proof of the installation date is unavailable, then six 

months after the date of manufacture will be used.

What is not covered?

Navien’s Limited Warranty shall be void in the event 

of an occurrence of any of the following:

 

Improper installation, including but not limited 

to, installation in violation of applicable rules, 

laws or building codes, inadequate water quality, 

condensate damage, improper venting, incorrect 

gas type, water pressure, absence of a drain pan, 

improper conversion from Natural Gas source to 

Propane, reinstallation at another location, etc.

 

Accident, abuse or misuse including but not 

limited to installation for non- recommended 

uses, failure to follow or comply with the User’s 

Operational Manual, etc.

 

Improper maintenance including but not limited 

to, scale buildup, vent blockage, failure to 

maintain, etc.

 

Modification, alteration, addition of non-

approved components, or misapplication of the 

Product in any manner.

 

Any damage caused by local adverse conditions 

including but not limited to water quality, 

hard water deposits, lime or mineral build-up, 

operating in corrosive atmospheric elements, 

alterations in smell or taste of water that have an 

adverse reaction on the unit, etc.

 

Damage or problems caused by gas flow issues, 

electrical surges, flooding, fire, freezing, abnormal 

external temperature, force majeure, riot, act of 

war, or any acts of God.

 

Performance problems caused by improper sizing 

of the boiler, the gas supply line, the venting 

connection, combustion air openings, electric 

service voltage, wiring, fusing or any other 

components, parts or specifications.

 

Vibration and noise unless caused by a defect in 

materials or workmanship. Any other causes other 

than defects in materials or workmanship.

 

Operating the Product at water temperatures 

outside the factory calibrated temperature limits 

and/or exceeding the maximum setting of the 

high limit control.

Содержание NFB-175H




























Отзывы: