Navico Lowrance LVR-880US Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 60

Navico Lowrance LVR-880US Скачать руководство пользователя страница 17

17

7. Press ENT to store the changes. The waypoint list is displayed again. If more changes are

required, repeat steps 2 through 6. Otherwise, press EXIT to cancel any edits.

3.1.3

Go to a New Waypoint

MENU SELECT
>WAYPOINT
BACKLIGHT
BUDDY LIST

WAYPOINT

>WP LIST
NEAREST WP
TEMP

WP

LIST

R14W05
R14W04

R14W03

R01W01

WP EDIT
DELETE
>GO

1.  Select WAYPOINT then WP LIST.
2.  Your waypoint list is displayed. Press ENT.
3.  NEW WP starts to flash. Scroll down to the waypoint you want to go to.  The selected waypoint

flashes. Press ENT again.

4. Select GO. The waypoint is set immediately as the destination waypoint.

Tip: If you are in the NAV big number screen, just turn the Channel Select knob to immediately access
the Waypoint List. Select the new waypoint and press ENT.

3.1.4

Go to Nearest Waypoint (NEAREST WP)

MENU SELECT
>WAYPOINT
BACKLIGHT
BUDDY LIST

WAYPOINT

WP LIST
>NEAREST WP
TEMP

NEAREST WP

>R01W04 001°
98nm
R01W03 003°
136nm

1. Select WAYPOINT then NEAREST WP.
2. Press ENT to display the nearest waypoint with distance and bearing from your current position.

Other waypoints are listed in increasing distance from your current position.

3. Press ENT to set the nearest waypoint as the active waypoint OR move the cursor to another

waypoint and then press ENT.
The chosen waypoint is shown on the bottom line of the LCD.

3.1.5

Go to Temporary Waypoint

MENU SELECT
>WAYPOINT
BACKLIGHT
BUDDY LIST

WAYPOINT

WP LIST
NEAREST WP
>TEMP

TEMP

>TEMP1
TEMP2

TEMP1

>GO
EDIT
DELETE

1.  Select WAYPOINT then TEMP.
2.  Your temporary waypoint list is displayed. There are 3 choices for quick access.
3.  Select the temporary waypoint to go to. Press ENT.
4.  Press ENT to set the temporary waypoint as the destination waypoint. It is immediately shown on

the bottom line of the LCD.

Tip: Hold down MOB and release before the 3 second countdown completes. Your current LL position
is stored in TEMP1 to TEMP3 in the waypoint list. If the list is full, a message appears asking if the
oldest location can be overwritten:

NEW WP
R01W02
R01W01

«
...
15
16
17
18
19
...
»

Содержание Lowrance LVR-880US





























































Отзывы:

Нет отзывов