manualshive.com logo in svg

NAVAC NTW1, Руководство пользователя, Страница: 9 / 12

Поделиться
Скачать
NAVAC NTW1 Скачать руководство пользователя страница 9

 
 

8 

 

 

TRACK MODE OPERATION 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Buzzer 

 

((((((((                ))))))))         (((((((          ))))))) 

Apply Torque 

 

 

Current Torque Value 

 

Current Torque Value 

 

 

*Note 1

 

START 

 

(System initial)

 

((…((…              …))…))   ((…((…          …)) …)) 

 
 

Buzzer 

 

Red LED 

Approached Target Torque

 

 

Setting Target Torque 

 

Green LED 

Reach 80% of Target Torque 

 

Reach Target Torque

 

 

Reach 80% of  Target Torque

 

 

*Note 3

 

*Note 2

 

Note:  

1.

 

If   

 is  displayed,  that  means  this  wrench  has  applied 

more than 110% of torque of the spec. 

2.

 

When  80%  of  the  target  torque  is  reached,  the  green  LED  will 
begin to flash and the alarm tone will beep intermittently. 

3.

 

When the target torque is approached, the alarm will change to 
a steady tone and the green LED will stop flashing and stay on. 
The red LED will also illuminate. 

 

Содержание NTW1













Отзывы:

Нет отзывов