NAVAC NTW1 Скачать руководство пользователя страница 10

Страница: 10 / 12

PEAK HOLD MODE OPERATION

Red LED

Approached Target Torque

Buzzer

(((((((( )))))))) ((((((( )))))))

Reach Target Torque

Current Torque Value

(Peak Hold)

START

Apply Torque

((…((… …))…)) ((…((… …)) …))

Buzzer

Green LED

Reach 80% of Target Torque

Flashing

Apply Torque

Released

Setting Target Torque

Reach 80% of Target Torque

Recording

*Note 2

*Note 1

(System initial)

*Note 3

*Note 4

Note:

is displayed, that means this wrench has ever been

applied more than 110% of torque of the spec.

is displayed, that means the wrench’s memory is

full and the next value record can not be written in. Please refer
the “Peak Hold Mode Recorded Value Review” section to clear
the momory records.

When 80% of the target torque is reached, the green LED will
begin to flash and the alarm tone will beep intermittently.

When the target torque is approached, the alarm will change to a
steady tone and the green LED will stop flashing and stay on.
The red LED will also illuminate.

Содержание NTW1













Результаты поиска

Содержание NTW1

Отзывы:

NAVAC NTW1, Руководство пользователя, Страница: 10 / 12

Результаты поиска

Содержание NTW1

Отзывы: