BHM
07/6/15
NTV-DOC209
Agreement
:
End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
5 |
P a g e
SVS-6 Installation
for aftermarket radio screens
Note: This section of the installation is intended for aftermarket screens, equipped with a composite reverse
camera (RVC) input & analog (wire) reverse trigger.
1.
Remove the vehicle’s radio/screen. You must gain access to the required location when installing an
aftermarket rear camera. Refer to the installation manual of the head unit in use if necessary.
2.
From the main SVS-6 harness, connect the black wire to ground (-) and the red wire to an ACC 12v (+)
source.
3.
Connect the (male) ‘
VIDEO OUT’ RCA
from the provided
CAM I/O Harness
to the
rear
camera input port
of the head unit.
4.
Connect the
Reverse OUTPUT wire (pin 21, blue)
to the RVC trigger wire on the head unit
(typically purple or purple/white).
5.
Mount and install all cameras (front, rear, trailer, aux video and blind-spot cameras) and run
video signal/power leads to the location where the SVS-6 will be mounted.
Camera Installation Notes:
a.
Use a vehicle switched
ACC 12v
wire to power your cameras.
Make sure the ACC source
you’re using has sufficient current to power all of your cameras. A thicker-gauge
wire (constant 12v) can be used for power supply to a relay, and trigger the relay
with an ACC source if you’re not sure.
b.
Connect each camera signal to each yellow RCA input per their specific labels (rear,
front, right TSC, left TSC etc).
6.
Connect the
vehicle’s
OEM reverse wire
to
input 6 (pin 9, white/black).
Note: if this wire was already
connected to the existing head unit’s RVC trigger, disconnect it and connect it here (pin 9) instead. The
head unit’s RVC trigger must connect to the SVS-6 module at pin 21. See diagram, page 7.
7.
Locate, test, splice and extend the
left & right vehicle turn signal wires
(wires will show 12v whenever
the bulb is illuminated) to the location where the SVS-6 will be mounted.
These wires can typically be found at the physical OEM turn signal lever harness beneath the
steering wheel shroud. In some vehicles, you may find them at the BCM.
Note: These triggers must
be positive (+) polarity to the SVS-6.
If the signals are negative, use relays for pole reversal.
8.
Connect the vehicle’s left turn signal to
input 5 (pin 10, purple).
Connect the vehicle’s right turn signal
to
input 4 (pin 11, pink)
.
9.
If a front camera was installed, connect
input 2 (pin 24, brown)
to an accessory 12v (+) source
through
a toggle or momentary button (not included) for activation.
Note: if using a momentary button, DIP
Switch #4 must be in the UP position for 12 second Front-CAM time-out.
10.
Optional:
If adding an AUX video source to the
AUX RCA input
, connect
input 3 (pin 23, gray/red)
to an
accessory 12v (+) source
through a toggle (not included) for activation or use a NAV-TV S2P.
11.
Optional:
If adding a Trailer Camera source to the
Trailer CAM input,
any time this input RCA sees a
video source, this video input will take priority over the regular RVC video input port.
This is a great
option if the user often connects a trailer for
automatically
displaying the proper camera while in
reverse.
12.
Connect the SVS-6 module to the 24-pin plug and proceed to ‘SVS-6 Operation’ (page 6).
