background image

BHM 

10/09/15 

NTV-DOC243 

 

 

 

Agreement

End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for 

misuse of its product.  If you do not agree, please discontinue use immediately and return product to place of purchase. This product is 

intended for off-road use and passenger entertainment only.  

3 | 

P a g e

 

 

AUDI-DYN-EXT Installation 

 
 
 
 

1.

 

Remove the factory radio (CD). Depending on the vehicle, this will require EURO tools or 
just prying the climate control panel from the sides (use plastic tools!). Disconnect all 
harnesses and set the radio aside.  

2.

 

Remove/drop the glovebox. This requires removing multiple 
8mm bolts which secure it to the dash. 

In some vehicles the 

pocket or single DIN media-gateway must be removed to 
access a bolt for removal

.    

a.

 

Remove this beauty panel 

before dropping glove box

 

(newer AUDI’s, beneath glove box):  

 

3.

 

Connect the provided 

LVDS-IN Cable

 to the 

OEM radio at the 

pink

 connector (no nav) or 

gray

 connector (with nav). This connector is 

keyed and will only fit in one direction. Run 
the other end of this cable out to the glove 
box area and connect to the interface plug 
labeled ‘VIDEO IN’. 
 

4.

 

Connect the 

OEM

 pink (or gray) circular HSD connector previously connected to the 

radio (removed in step 1) to the green port on 
the interface labeled 

‘VIDEO OUT’

You may 

need to unwrap/cut factory tape for it reach 
the module with proper slack.  

5.

 

Reconnect remaining plugs to the radio and carefully place it back into the dash. Don’t 
secure the radio until fully tested.  
 

6.

 

Optional: 

If this car is 

not

 equipped with OEM rear parking sensors, you may turn the 

PDC off in the OSD menu system (see page 7 for menu information). 

Note:

 If adjusting any RVC or AUX Video menu settings, temporarily connecting the 

provided IR-Eye is 

required

.

 The IR connector is located among the main power harness (2-pin 

& 3-pin).  See menu settings on page 7 for more info.  

ATTENTION INSTALLER: All connections (including CAN) must be made BEFORE 

connecting the power harness to this unit for proper startup operation. 

 

Содержание NTV-KIT701










Отзывы: