Nautel NV30LT-N Скачать руководство пользователя страница 29

Страница: 29 / 226

NV30LT-N OPERATIONS & MAINTENANCE MANUAL

OPERATING THE TRANSMITTER

VERSION 0.1 2015-03-01

PAGE 3.2.11

Front Panel UI Screens

Table 3.2.1

defines the available front panel display screens.

Table 3.2.1: Front Panel UI Screens

UI Screen

Function

See Page

Main Menu

Choose options and navigate to other screens.

page 3.2.9

Select Preset

Select and activate a user-defined preset.

page 3.2.65

User Settings

Edit various transmitter user settings (see other User Settings options in
this table).

User Settings - Edit Presets

Edit various parameters for a user-defined preset (see the following
rows for all Edit Presets options).

page 3.2.65

User Settings - Edit Presets -
Output Power

Edit the selected preset’s output power.

page 3.2.67

User Settings - Edit Presets -
Frequency

Edit the selected preset’s operating frequency.

page 3.2.67

User Settings - Edit Presets -
Main Audio

Edit the selected preset’s main audio characteristics such as source,
stereo mode, pre-emphasis and low pass filtering.

page 3.2.68

User Settings - Edit Presets -
Backup Audio

Enable and edit the selected preset’s backup audio characteristics such
as source, stereo mode, pre-emphasis and low pass filtering.

page 3.2.70

User Settings - Edit Presets -
Pilot Settings

Edit the selected preset’s pilot settings such as level, phase and 1 PPS
synchronization.

page 3.2.71

User Settings - Edit Presets -
SCA Settings

Edit the selected preset’s SCA settings such as SCA reduction, MPX
SCAs, MPX SCA input and internal SCA (1 and 2) generator
characteristics.

page 3.2.72

User Settings - Edit Presets -
RDS Settings

Edit the selected preset’s RDS settings such as enable/disable, data
source, baud rate, level, phase, program type, alternate frequency data,
etc.

page 3.2.74

User Settings - Edit Presets -
Limiter Settings

Edit the selected preset’s limiter settings. Limiter types include hard
limiter, AGC limiter, 2-slope limiter, L/R limiter and MPX RMS limiter.

page 3.2.79

User Settings - Edit Presets -
Mod Loss

Edit the selected preset’s modulation loss functionality, such as enable/
disable, setting threshold, setting timeout period, setting resulting
action and selecting a backup preset.

page 3.2.83

User Settings - Edit Presets -
Audio Delay

Edit the selected preset’s audio delay.

page 3.2.85

Содержание NV30LT-N



































































































































































































































Результаты поиска

Содержание NV30LT-N

Отзывы:

Бренды по названию

Популярные бренды

Nautel NV30LT-N, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание NV30LT-N

Отзывы:

Бренды по названию

Популярные бренды