Nautel Exporter Plus Скачать руководство пользователя страница 24

Страница: 24 / 186

Exporter Plus Technical Instruction Manual

Pre-installation tasks

Page 2-2

Issue 1.0 2020-05-05

Selecting a location for the Exporter Plus

To ensure that the desired location for the Exporter Plus is suitable, perform the following

tasks.

1. Ensure you have a cabinet and room space suitable for installing the Exporter Plus.

Also, though it is not required, a UPS is recommended to avoid interrupts due to

brown-out conditions. Refer to

“Exporter Plus at Transmitter Site” on page 1-4

for

dimensions and clearances.

2. In addition, it is normal to insert

MPS

audio processing on both of the

MPS

audio paths

to the Exporter Plus. Since one path is for the

IBOC MPS

and the other is for analog

MPS

, audio processing requirements are different, requiring two audio processors

(

Figure 2.1

Figure 2.1: GPS sync PWB audio processor connections

3. Ensure the Exporter Plus is near a standard 120 V ac power outlet.

4. The Exporter Plus contains a GPS receiver that must be connected to a GPS antenna

(

Figure 2.2

) that has a clear view of the sky. The supplied GPS antenna cable is 50 feet

long, and the cone-shaped antenna mounts on a user-supplied pole.

Exporter Plus

Audio

Processor

Audio

Processor

MPS Audio

IBOC

MPS Audio

Analog

MPS Audio

Содержание Exporter Plus



























































































































































































Результаты поиска

Содержание Exporter Plus

Отзывы:

Nautel Exporter Plus, Техническое руководство по эксплуатации, Страница: 24 / 186

Результаты поиска

Содержание Exporter Plus

Отзывы: