background image

Nicolet Cortical Stimulator

1-8

Revised 8/27/13

System 
configuration 
disclaimers

a) Antivirus and third party software and hardware 

Natus Neurology Incorporated manufactures hardware and software to be used 
on or with standard PC-compatible computers and operating software. Natus 
Neurology Incorporated, however, assumes no responsibility for the use or 
reliability of its software or hardware with equipment that is not furnished by 
third-party manufacturers accepted by Natus Neurology Incorporated at the date 
of purchase. This includes third-party software packages that are installed on 
Natus Neurology Incorporated products or affect Natus Neurology Incorporated 
products through operation over a network.

Active scanning with Anti-Virus Software is not recommended on any Natus 
Neurology Incorporated instrument. Active and Normal scanning are not allowed 
during acquisition of patient data. Anti-Virus software will interrupt the 
recording, resulting in complete or partial inability to record patient data. Natus 
Neurology Incorporated network consultants can recommend network and 
antivirus software configurations for Natus Neurology Incorporated equipment 
which will be secure without the use of active or normal scanning. Failure to 
follow these guidelines may void the system warranty.

b) Microsoft updates

Natus Neurology Incorporated verifies and validates it software with all 
Microsoft Service Pack updates available at the time of Natus Neurology 
Incorporated software release. Customer Group Policy should isolate Natus 
Neurology Incorporated systems from getting Microsoft updates pushed 
automatically and / or a System “Restore Point” should be established before any 
Microsoft updates are done to ensure that those updates can be rolled back if they 
conflict with the Natus Neurology Incorporated clinical applications. Contact a 
Natus Neurology Incorporated Service representative to determine which 
Microsoft Service Packs have been verified and validated with Natus Neurology 
Incorporated software.

Содержание Nicolet SCU





































































Отзывы: