manualshive.com logo in svg

natus ErgoJust ICU, Инструкция по установке и эксплуатации, Страница: 38 / 92

Поделиться
Скачать
natus ErgoJust ICU Скачать руководство пользователя страница 38

ErgoJust and ErgoJust ICU Cart Installation and Functionality Guide

3-12

August 22, 2017

Mounting the Natus Photic Stimulator (option)

1. Insert the optional Natus Photic Stimulator mounting post into the accessory bar (Figure 1). It 

may be located on either side of the main post.

2. Tighten the securing knob to secure the post.

3. Route the power cable down to the cart base and secure the power supply with Velcro

  Figure 1: Mounting the Natus Photic Stimulator (option) swivel arm.

Mounting the Natus Amplifier Base Unit

NOTE:

Ensure the Amplifier Base Unit has a Headbox Side Quick Disconnect Bracket attached.

1. Insert the four mounting pins on the rear of the Amplifier Base Unit into the four mounting 

holes on the video pole side quick disconnect bracket (Figure 1) and slide the Amplifier Base 
Unit downward until the locking pin snaps into the quick disconnect bracket locking hole.

2. To remove the Amplifier Base Unit, pull the locking pin out to the Release position and slide 

the Amplifier Base Unit upward and away from the cart.

  Figure 1: Mounting and removing the Amplifier Base Unit.

Содержание ErgoJust ICU





























































































Отзывы:

Нет отзывов