National Semiconductor DP83816AVNG Скачать руководство пользователя | Manualshive

Страница: 7 / 108

background image

6

www.national.com

2.0 Pin Description

(Continued)

DP83816

SERRN

98

I/O

System Error:

This signal is asserted low by DP83816 during address parity errors

and system errors if enabled.

STOPN

96

I/O

Stop:

This signal is asserted low by the target device to request the master device

to stop the current transaction.

TRDYN

93

I/O

Target Ready:

As a master, this signal indicates that the target is ready for the data

during write operation and with the data during read operation. As a target, this
signal will be asserted low when the (target) device is ready to complete the current
data phase transaction. This signal is used in conjunction with the IRDYN signal.
Data transaction takes place at the rising edge of PCICLK when both IRDYN and
TRDYN are asserted low.

PMEN/

CLKRUNN

59

I/O

Power Management Event/Clock Run Function:

This pin is a dual function pin.

The function of this pin is determined by the CLKRUN_EN bit 0 of the CLKRUN
Control and Status register (CCSR). Default operation of this pin is PMEN.

Power Management Event:

This signal is asserted low by the DP83816 to indicate

that a power management event has occurred. For pin connection please refer to
Section 6.7.

Clock Run Function:

In this mode, this pin is used to indicate when the PCICLK

will be stopped.

3VAUX

122

I

PCI Auxiliary Voltage Sense:

This pin is used to sense the presence of a 3.3V

auxiliary supply in order to define the PME Support available. For pin connection
please refer to Section 6.7.

This pin has an internal weak pull down.

PWRGOOD

123

I

PCI bus power good:

Connected to PCI bus 3.3V power, this pin is used to sense

the presence of PCI bus power during the D3 power management state.

This pin has an internal weak pull down.

PCI Bus Interface

Symbol

LQFP Pin

No(s)

Dir

Description

«
...
5
6
7
8
9
...
»

Содержание DP83816AVNG













































































































Отзывы:

Нет отзывов

Похожие инструкции для DP83816AVNG

Бренд: H3C Страницы: 1057

Бренд: National Instruments Страницы: 34

Бренд: H3C Страницы: 400

Бренд: FOR-A Страницы: 39

ICS-G7748A Series

Бренд: Moxa Technologies Страницы: 10

Бренд: X-Micro Страницы: 49

Бренд: Airlink101 Страницы: 13

Бренд: Hamlet Страницы: 11

Бренд: Comtrend Corporation Страницы: 69

Бренд: Devolo Страницы: 24

Бренд: Hama Страницы: 34

Бренд: D-Link Страницы: 12

FrameSaver DSL 9783 CSU/DSU

Бренд: Paradyne Страницы: 233

Бренд: Sarian Systems Страницы: 9

SWC-2100 (VoIP CPE)

Бренд: SEOWON INTECH Страницы: 46

Бренд: TP-Link Страницы: 186

Бренд: MikroTik Страницы: 7

Бренд: Oki Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды