National Semiconductor DP83816AVNG Скачать руководство пользователя | Manualshive

Страница: 41 / 108

background image

40

www.national.com

4.0 Register Set

(Continued)

DP83816

4.2.2 Configuration and Media Status Register

This register allows configuration of a variety of device and phy options, and provides phy status information.

Tag:

CFG

Size:

32 bits

Hard Reset:

00000000h

Offset:

0004h

Access:

Read Write

Soft Reset:

00000000h

Bit

Bit Name

Description

31

LNKSTS

Link Status

Link status of the internal phy. Asserted when link is good. RO

30

SPEED100

Speed 100 Mb/s

Speed 100 Mb/s indicator for internal phy. Asserted when speed is set or has negotiated to 100 Mb/s.
De-asserted when speed has been set or negotiated to 10 Mb/s. RO

29

FDUP

Full Duplex

Full Duplex indicator for internal phy. Asserted when duplex mode is set or has negotiated to FULL. De-
asserted when duplex mode has been set or negotiated to HALF. RO

28

POL

10 Mb/s Polarity Indication

Twisted pair polarity indicator for internal phy. Asserted when operating and 10 Mb/s and the polarity has
been detected as reversed. De-asserted when polarity is normal or phy is operating at 100 Mb/s. RO

27

ANEG_DN

Auto-negotiation Done

Auto-negotiation done indicator from internal phy. Asserted when auto-negotiation process has
completed or is not active. RO

26-24

unused

23-18

PHY_CFG

Phy Configuration

Miscellaneous internal phy Power-On-Reset configuration control bits.

17

PINT_ACEN

Phy Interrupt Auto Clear Enable

When set to a 1, this bit allows the phy interrupt source to be automatically cleared whenever the ISR is
read. When this bit is 0, the phy interrupt source must be manually cleared via access of the phy
registers. R/W

16

PAUSE_ADV

Pause Advertise

This bit is loaded from EEPROM at power-up and is used to configure the internal phy to advertise the
capability of 802.3x pause during auto-negotiation. Setting this bit to 1 will cause the pause function to be
advertised if the phy has also been configured to advertise full duplex capability (See ANEG_SEL). R/W

15-13

ANEG_SEL

Auto-negotiation Select

These bits are loaded from EEPROM at power-up and are used to define the default state of the internal
phy auto-negotiation logic. R/W These bits are encoded as follows:

000 Auto-negotiation disabled, force 10 Mb/s half duplex

010 Auto-negotiation disabled, force 100 Mb/s half duplex

100 Auto-negotiation disabled, force 10 Mb/s full duplex

110

Auto-negotiation disabled, force 100 Mb/s full duplex

001 Auto-negotiation enabled, advertise 10 Mb/s half & full duplex

011

Auto-negotiation enabled, advertise 10/100 Mb/s half duplex

101 Auto-negotiation enabled, advertise 100 Mb/s half & full duplex

111

Auto-negotiation enabled, advertise 10/100 Mb/s half & full duplex

12

EXT_PHY

External Phy Support

Act as a stand-alone MAC. When set, this bit enables the MII and disables the internal Phy (sets bit 9).
R/W

11

Reserved

«
...
39
40
41
42
43
...
»

Содержание DP83816AVNG













































































































Отзывы:

Нет отзывов

Похожие инструкции для DP83816AVNG

i-bus KNX IPR/S 3.5.1

Бренд: ABB Страницы: 44

OfficeConnect 1600

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

Бренд: National Instruments Страницы: 34

Бренд: Vivotek Страницы: 136

Fast SwitchHub-8mi SNMP

Бренд: Accton Technology Страницы: 13

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: I-O Wireless Страницы: 55

Бренд: U.S. Products Страницы: 80

IBOX-BAC Series

Бренд: IntesisBox Страницы: 2

WRT54GR - Wireless-G Broadband Router

Бренд: Linksys Страницы: 81

ConnectX-3 Pro MCX349A-XCCN

Бренд: Mellanox Technologies Страницы: 35

Бренд: Multi-Link Страницы: 31

Бренд: MicroNova Страницы: 113

Бренд: Ruckus Wireless Страницы: 4

Бренд: Siklu Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды