manualshive.com logo in svg

National Instruments SCXI-1351, Руководство по установке

Поделиться
Скачать
National Instruments SCXI-1351 Скачать руководство пользователя страница 3

©

National Instruments Corporation

3

SCXI-1351 One-Slot Cable Extender

•

Pollution degree 3 means that conductive pollution occurs, or dry,
nonconductive pollution occurs that becomes conductive due to
condensation.

Clean the product with a soft nonmetallic brush. Make sure that the product
is completely dry and free from contaminants before returning it to service.

You

must

insulate signal connections for the maximum voltage for which

the product is rated. Do

not

exceed the maximum ratings for the product.

Remove power from signal lines before connecting them to or
disconnecting them from the product.

Operate this product only at or below the installation category stated in the

Specifications

section.

The installation category for this device, installation category I, is for
measurements performed on circuits not directly connected to MAINS

1

.

This category is a signal level such as voltages on a printed wire board
(PWB) on the secondary of an isolation transformer.

Examples of installation category I are measurements on circuits not
derived from MAINS and specially protected (internal) MAINS-derived
circuits.

1

MAINS is defined as the electricity supply system to which the equipment concerned is designed to be connected either for
powering the equipment or for measurement purposes.

Содержание SCXI-1351












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды