background image

Table 5. SCB-19 Signal Descriptions (Continued)

Pin

Signal

Description

 

 

 

8

NC

No connection

9

PFI 4

Bidirectional PFI line

10

PFI 5

Bidirectional PFI line

11

PFI 6

Bidirectional PFI line

12

PFI 7

Bidirectional PFI line

13

+3.3 V

+3.3 V power (200 mA maximum)

<14..26>

GND

Ground reference for signals

Configuring the PXIe-5413 in MAX

Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX
informs other programs about which NI hardware products are in the system and how they are
configured. MAX is automatically installed with NI-FGEN.
1.

Launch MAX.

2.

In the configuration tree, expand 

Devices and Interfaces

 to see the list of installed NI

hardware.

Installed modules appear under the name of their associated chassis.

3.

Expand your 

Chassis

 tree item.

MAX lists all modules installed in the chassis. Your default names may vary.

Note

 

If you do not see your module listed, press <F5> to refresh the list of

installed modules. If the module is still not listed, power off the system, ensure
the module is correctly installed, and restart.

4.

Record the identifier MAX assigns to the hardware. Use this identifier when
programming the PXIe-5413.

5.

Self-test the hardware by selecting the item in the configuration tree and clicking 

Self-

Test

 in the MAX toolbar.

The MAX self-test performs a basic verification of hardware resources.

Related Information

What Should I Do if the PXIe-5413 Doesn't Appear in MAX?

 on page 15

What Should I Do if the PXIe-5413 Fails the Self-Test or Self-Calibration?

 on page 15

PXIe-5413 Getting Started Guide

  | 

© National Instruments

  | 

11

Содержание PXIe-5413



















Отзывы: