National Instruments PXI-8187 Скачать руководство пользователя

Страница: 41 / 69

Chapter 3

I/O Information

NI PXI-8186/8187 User Manual

3-12

ni.com

Front Panel Features

The NI PXI-8186/8187 has the following front-panel features:

•

A system reset pushbutton (press the button to generate a reset to the
controller)

•

Two front panel LEDs that show PC status

–

The

POWER OK

LED indicates that the power is on and reset

is no longer asserted.

–

The

DRIVE

LED indicates when an access to the internal hard

disk is occurring.

Data Storage

The NI PXI-8186/8187 has the following data storage features:

•

Internal IDE hard drive

–

2.5 in. notebook hard drive

–

Supports up to ATA-5 (UDMA 100)

•

USB storage support—USB CD-ROM, mass storage device, or floppy
drive

SRQ*

Service Request

ATN*

Attention

SHIELD

Chassis ground

DIO5*

Data Bit 5

DIO6*

Data Bit 6

DIO7*

Data Bit 7

DIO8*

Data Bit 8

REN*

Remote Enable

18–25

GND

Logic Ground

Table 3-9.

GPIB Connector Signals (Continued)

Pin

Signal Name

Signal Description

Содержание PXI-8187






































































Результаты поиска

Содержание PXI-8187

Отзывы:

Похожие инструкции для PXI-8187

Бренды по названию

Популярные бренды

National Instruments PXI-8187, Руководство пользователя

Результаты поиска

Содержание PXI-8187

Отзывы:

Похожие инструкции для PXI-8187

Бренды по названию

Популярные бренды