National Instruments PXI-8186 Скачать руководство пользователя | Manualshive

Страница: 21 / 69

background image

Chapter 2

Installation and Configuration

NI PXI-8186 User Manual

2-8

ni.com

•

Parallel Port Mode

—The PC industry has created several different

modes of operation for this port over the years. Usually, the default
setting works for all applications. However, if a parallel port device
specifically requires a nondefault setting, you can change it here.
The default is

Bidirectional

, for full IEEE 1284 capabilities.

•

Legacy USB Support

—Use this setting to use a USB keyboard and

mouse as if they were standard PS/2-style peripherals. You

must

enable

this setting to use these devices in operating systems with no USB
support and to boot from a USB floppy or CD-ROM. The BIOS setup
screen always works with USB keyboards regardless of this setting.
Certain real-time applications may require you to disable this setting
to reduce loop time jitter. The default is

Enabled

.

LabVIEW RT Options Submenu

Use this menu to configure boot options for LabVIEW RT if it is installed
on the controller. If you are not using LabVIEW RT, you should leave these
settings as default.

Note

These settings override the behavior of the switches on S1. Refer to the

RT Configuration Switches

section for more information. To use the settings from the

switches, select

Use Hardware Switch

for each option.

•

Boot Configuration

—This setting selects whether the controller

should boot LabVIEW RT, LabVIEW RT Safe Mode, or an installed
OS such as Windows XP. The default is

Use Hardware Switch

.

•

Disable Startup VI

—If the controller becomes inaccessible because

of a startup VI, this switch can prevent VIs from automatically running
at startup. The default is

Use Hardware Switch

.

•

Reset IP Address

—If the controller is deployed to a different subnet

from which it was originally configured, or if the current IP address
is invalid, use this switch to reset the IP address to 0.0.0.0 during
LabVIEW RT startup. The default is

Use Hardware Switch

.

PXI Setup Menu

Use this menu to control and route certain signals on the PXI backplane.
Normally, you do not need to modify these settings. However, other
sections of this manual may indicate that modifications are necessary
and may lead to unpredictable behavior.

•

INTP Routing

—You can route INTP to ISA IRQ 14, for use by a

PXI device functioning as a Primary IDE Controller. The default
setting is

Not Routed

.

«
...
19
20
21
22
23
...
»

Содержание PXI-8186






































































Отзывы:

Нет отзывов

Похожие инструкции для PXI-8186

Бренд: ZETR Страницы: 2

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: Ublox Страницы: 116

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

HAWA-Frontside 60/B

Бренд: hawa Страницы: 28

Бренд: FOR-A Страницы: 39

Бренд: Delta Electronics Страницы: 1

Бренд: IOtech Страницы: 16

Бренд: NA Страницы: 22

Бренд: Zoom Страницы: 48

Active Module Carrier VX402C-64

Бренд: C&H Страницы: 32

Бренд: Abit Страницы: 22

Suzie-Q 541.35.520

Бренд: Hafele Страницы: 12

Бренд: Alula Страницы: 4

Бренд: Compal Страницы: 47

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренд: ATI Technologies Страницы: 87

Бренд: Z3 Technology Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды