National Instruments PXI-8119 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 88

background image

Chapter 2

Installation and Configuration

©

National Instruments

2-7

NI PXI-8119 User Manual

SATA Configuration Submenu

Use this submenu to apply alternate settings to the hard disk drive (HDD)
interfaces. Normally, you do not need to modify these settings, as the
factory default settings provide the most compatible and optimal
configuration possible.

•

SATA Controller

—This setting specifies whether or not the onboard

SATA controller is enabled or disabled. The default value is

Enabled

.

–

SATA Mode Selection

—This setting determines whether AHCI

mode is enabled or disabled for the SATA port. Some operating
systems, such as Windows 2000, do not support AHCI mode. You
can use this setting to disable AHCI mode and enable IDE mode
so that non-compatible OSes function correctly. The default value
is

AHCI

.

•

Internal Drive (SATA)

—This item displays the onboard SATA drive

detected in the system.

CPU Configuration Submenu

Use this submenu to apply alternate settings to the CPU. Normally, you do
not need to modify these settings, as the factory default settings provide the
most compatible and optimal configuration possible.

•

Hyper-Threading

—This setting enables or disables Intel

Hyper-Threading technology. The default value is

Enabled

. Enabling

Hyper-Threading increases performance for some applications by
adding virtual CPU cores. Hyper-Threading can increase application
jitter, so care should be taken when enabling this setting on a
Real Time system. When the BIOS is configured to boot LabVIEW
Real-Time, Hyper-Threading will be automatically disabled. In order
to manually enable Hyper-Threading performance when in LabVIEW
Real-Time mode, see the

LabVIEW RT Configuration Overrides

Submenu

.

•

Enabled CPU Cores

—This setting selects the number of active CPU

cores for the processor. Valid values are

All

,

3

,

2

,

1

. The default value

is

All

.

•

Turbo Boost

—This setting enables or disables Intel Turbo Boost

technology. The default value is

Enabled

. Enabling Turbo Boost

allows CPU cores to run at higher than their base frequency for short
durations, while other cores are idle. Enabling Turbo Boost can also
increase application jitter, so care should be taken when enabling this
setting on a Real Time system. To achieve maximum possible Turbo
Boost frequencies, also enable the C-States setting.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
22
23
24
25
26
...
»

Содержание PXI-8119

























































































Отзывы:

Нет отзывов

Похожие инструкции для PXI-8119

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: Hankscraft Runxin Страницы: 53

Бренд: Samsung Страницы: 27

Бренд: ZETRON Страницы: 3

Бренд: ADEMCO Страницы: 2

Бренд: V2 ELETTRONICA Страницы: 72

Бренд: National Instruments Страницы: 102

Бренд: NAU ROBOTICS Страницы: 109

Maschine Mikro MK2

Бренд: Native Instruments Страницы: 181

Бренд: Patron Страницы: 36

Бренд: Insignia Страницы: 2

Бренд: Thermomart Страницы: 6

Бренд: Measurement Computing Страницы: 32

Бренд: Valence Tech Страницы: 12

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

Бренд: Atmel Страницы: 12

Бренд: OLYS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды