National Instruments PXI-8110 Скачать руководство пользователя

Страница: 80 / 85

National Instruments Corporation

I-1

NI PXI-8110 User Manual

Index

Advanced Setup menu, 2-6

basic PXI system configuration, 2-23
battery replacement and disposal

information, A-6

BIOS

checking settings, 4-1
flashing new BIOS, 4-5
setup

Advanced Setup menu, 2-6
Boot Settings Configuration menu,

2-13

Boot Setup menu, 2-12
CD/DVD ROM Drive BBS Priorities

Configuration menu, 2-13

CPU configuration menu, 2-8
entering, 2-5
ExpressCard Configuration

menu, 2-9

Floppy Drive BBS Priorities

Configuration menu, 2-14

Hard Drive BBS Priorities

Configuration menu, 2-13

LabVIEW RT options menu, 2-11
Main Setup menu, 2-6
Network Device BBS Priorities

Configuration menu, 2-14

SATA Configuration menu, 2-7
Save & Exit menu, 2-14
Serial/Parallel Port Configuration

menu, 2-10

Parallel Port menu, 2-10
Serial Port 0 menu, 2-10

Trigger Router Configuration menu,

2-11

USB configuration menu, 2-9
Video Configuration menu, 2-8

boot options, configuring controller, 4-2
Boot Settings Configuration menu, 2-13
Boot Setup menu, 2-12
budgeting, PXI system power, 2-26

CD/DVD ROM Drive BBS Priorities

menu, 2-13

CD-ROM drive, installing software from, 4-4
CE compliance specifications, A-5
chipset

ICH9M, 1-4
Mobile Intel GM45 Express, 1-4

CMOS

clearing contents (figure), 2-16, 5-3
setting back to default, 5-2

COM1 connector

connector locations and pinout

(figure), 3-5

connector signals (table), 3-5

common configuration questions

boot options, 4-1
chassis configuration, 2-22

figure, 2-22

driver installation, 4-3
general questions, 4-1
PXI configuration, 4-6
upgrade information, 4-4

CompactPCI specification, 1-1
configuration, common questions

boot options, 4-1
cables and connections, 4-2

Содержание PXI-8110






















































































Результаты поиска

Содержание PXI-8110

Отзывы:

Похожие инструкции для PXI-8110

Бренды по названию

Популярные бренды

National Instruments PXI-8110, Руководство пользователя

Результаты поиска

Содержание PXI-8110

Отзывы:

Похожие инструкции для PXI-8110

Бренды по названию

Популярные бренды