National Instruments PXI-8110 Скачать руководство пользователя

Страница: 28 / 85

Chapter 2

Installation and Configuration

National Instruments Corporation

2-13

NI PXI-8110 User Manual

•

CD/DVD ROM Drive BBS Priorities

—Use this setting to access the

CD/DVD ROM Drive BBS Priorities

submenu to re-order or disable

bootable CD/DVD ROM drive devices. Refer to the

CD/DVD ROM

Drive BBS Priorities Submenu

section for more information.

•

Floppy Drive BBS Priorities

—Use this setting to access the

Floppy

Drive BBS Priorities

submenu to re-order or disable bootable floppy

drive devices. Refer to the

Floppy Drive BBS Priorities Submenu

section for more information.

•

Network Device BBS Priorities

—Use this setting to access the

Network Device BBS Priorities

submenu to re-order or disable

bootable network devices. Refer to the

Network Device BBS Priorities

Submenu

section for more information.

Boot Settings Configuration Submenu

Use this submenu to apply alternate configurations to boot settings.
Normally, you do not need to modify these settings, as the factory default
settings provide the most compatible and optimal configuration.

•

Quiet Boot

—This setting enables or disables the splash screen during

the boot process. The default value is

Enabled

•

Setup Prompt Timeout

—This setting specifies the number of

seconds the system will wait for a BIOS Setup menu keypress
(the <Del> key). The default value is

second.

•

Bootup NumLock State

—This setting specifies the power-on state of

the keyboard NumLock setting. The default value is

Hard Drive BBS Priorities Submenu

•

Boot Option #1, Boot Option #2, Boot Option #3

—These settings

specify the boot priority of hard drive devices. The highest priority
device is displayed on the main

Boot Option Priorities

list.

Optionally, each device can also be

Disabled

if the device should never

be used as a boot device.

CD/DVD ROM Drive BBS Priorities Submenu

•

Boot Option #1, Boot Option #2, Boot Option #3

—These settings

specify the boot priority of CD/DVD ROM drive devices. The highest
priority device is displayed on the main

Boot Option Priorities

list.

Optionally, each device can also be

Disabled

if the device should never

be used as a boot device.

Содержание PXI-8110






















































































Результаты поиска

Содержание PXI-8110

Отзывы:

Похожие инструкции для PXI-8110

Бренды по названию

Популярные бренды

National Instruments PXI-8110, Руководство пользователя

Результаты поиска

Содержание PXI-8110

Отзывы:

Похожие инструкции для PXI-8110

Бренды по названию

Популярные бренды