National Instruments PXI-8110 Скачать руководство пользователя | Manualshive

Страница: 25 / 85

background image

Chapter 2

Installation and Configuration

NI PXI-8110 User Manual

2-10

ni.com

In addition, the following option is available for each detected device if a
USB mass storage device is present:

•

Emulation Type

—This setting specifies how the BIOS will present

the USB mass storage device to the system. This option can be used to
present a USB mass storage device as a floppy, Zip, hard disk, or
CD-ROM drive. The default is

Auto

, which allows the BIOS to treat

small USB flash disk drives as floppy drives and larger USB flash disk
drives as hard disk drives.

Serial/Parallel Port Configuration Submenu

Use this submenu to apply alternate configurations to the serial and
parallel ports. Normally, you do not need to modify these settings, as the
factory default settings provide the most compatible and optimal
configuration possible.

•

Serial Port 0 Configuration

—Use this setting to access the

Serial Port 0 Configuration

submenu. Refer to the

Serial Port 0

Configuration Submenu

section for more information.

•

Parallel Port Configuration

—Use this setting to access the

Parallel Port Configuration

submenu. Refer to the

Parallel Port

Configuration Submenu

section for more information.

Serial Port 0 Configuration Submenu

•

Serial Port

—This setting enables or disables the onboard serial port.

The default value is

Enabled

.

•

Device Settings

—This item displays the current base address and

interrupt request level (IRQ) information for the onboard serial port.

•

Change Settings

—This setting changes the base address and interrupt

request level (IRQ) information for the onboard serial port. The default
value is

Auto

.

Parallel Port Configuration Submenu

•

Parallel Port

—This setting enables or disables the onboard parallel

port. The default value is

Enabled

.

•

Device Settings

—This item displays the current base address and

interrupt request level (IRQ) information for the onboard parallel port.

•

Device Mode

—This settings enables alternate modes of operation for

the parallel port. Usually the default setting works for all applications.
The default is

STD Printer Mode

.

«
...
23
24
25
26
27
...
»

Содержание PXI-8110






















































































Отзывы:

Нет отзывов

Похожие инструкции для PXI-8110

Бренд: XMG Страницы: 5

Бренд: NAD Страницы: 2

Бренд: Magma Страницы: 2

Бренд: 3Com Страницы: 16

Бренд: Alcad Страницы: 6

Бренд: ZALMAN Страницы: 8

Бренд: AXIOMTEK Страницы: 2

Бренд: NEC Страницы: 70

Бренд: ETAS Страницы: 84

POD-51EH-C541U-12

Бренд: IceTech Страницы: 8

Бренд: Intel Страницы: 154

SATA II-150 PCI

Бренд: SIIG Страницы: 16

Hotwire 5620 RTU

Бренд: Paradyne Страницы: 20

Бренд: Advantech Страницы: 70

Бренд: Honeywell Home Страницы: 36

Бренд: M86 Security Страницы: 512

Бренд: Kvadrat Страницы: 9

Бренд: Emerson Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды