National Instruments PXI-8110 Скачать руководство пользователя | Manualshive

Страница: 39 / 85

background image

Chapter 2

Installation and Configuration

NI PXI-8110 User Manual

2-24

ni.com

Figure 2-7.

Installing a DDR2 SO-DIMM in an NI PXI-8110 Controller

Hard Drive Recovery

NI PXI-8110 controllers include two methods of restoring the original
factory condition of your hard drive. Hard drive-based recovery stores a
factory backup on a separate portion of your hard drive allowing you to
restore your controller without additional media. The NI PXI-8110
controller also ships with an OS Recovery CD that allows you to reinstall
your operating system onto your hard drive through an external CD-ROM.
For more information on these tools refer to KnowledgeBase 2ZKC02OK
at

ni.com/support

.

Note

Your system hot key is <F4>. To access the hard drive-based recovery tool, press and

hold <F4> when video first appears during the boot process.

If you need to recover your factory-installed operating system from a CD,
you can use the included OS re-installation CD with an external CD-ROM
drive such as a USB CD-ROM drive. Boot the PXI controller using the
OS re-installation CD to recover the OS. You also may need to reinstall
other software after using the CD to recover the OS.

1

DDR2

S

O-DIMM Mod

u

le

2

DDR2

S

O-DIMM

S

ocket

1

2

«
...
37
38
39
40
41
...
»

Содержание PXI-8110






















































































Отзывы:

Нет отзывов

Похожие инструкции для PXI-8110

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

Бренд: EVS Страницы: 30

Бренд: SIIG Страницы: 6

Бренд: EVOC Страницы: 57

Бренд: Valcom Страницы: 4

Бренд: IDT Страницы: 207

Бренд: Galaxy Страницы: 30

Бренд: ekwb Страницы: 11

Бренд: Baikal Miner Страницы: 14

Бренд: Kentrox Страницы: 246

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Altronix Страницы: 8

EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB

Бренд: EK Страницы: 9

C32C824151 - UB E02 Print Server

Бренд: Epson Страницы: 84

Бренд: Epson Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды