manualshive.com logo in svg

National Instruments PPC-2115, Руководство пользователя, Страница: 36 / 48

Поделиться
Скачать
National Instruments PPC-2115 Скачать руководство пользователя страница 36

Appendix D

Watchdog Timer Programming on WinCE

PPC-2115 User Manual

D-2

ni.com

can use these control codes with DeviceIoControl to perform 
driver-specific functions.

•

lpInBuffer

 

(in) Long pointer to a buffer that contains the data required to perform 
the operation. This parameter can be NULL if the 

dwIoControlCode

 

parameter specifies an operation that does not require input data.

•

nInBufferSize

 

(in) Size, in bytes, of the buffer pointed to by 

lpInBuffer

.

•

lpOutBuffer

 

(out) Long pointer to a buffer that receives the operation’s output data. 
This parameter can be NULL if the 

dwIoControlCode

 parameter 

specifies an operation that does not produce output data.

•

nOutBufferSize

 

(in) Size, in bytes, of the buffer pointed to by 

lpOutBuffer

.

•

lpBytesReturned

 

(out) Long pointer to a variable that receives the size, in bytes, of 
the data stored into the buffer pointed to by 

lpOutBuffer

. The 

lpBytesReturned

 parameter cannot be NULL. Even when an 

operation produces no output data, and 

lpOutBuffer

 can be 

NULL, DeviceIoControl makes use of the variable pointed to by 

lpBytesReturned

. After such an operation, the variable value has 

no meaning.

•

lpOverlapped

 

(in) Ignored; set to NULL.

•

Return Values

Nonzero indicates success. Zero indicates failure. To get extended 
error information, call GetLastError.

Содержание PPC-2115

















































Отзывы:

Нет отзывов