manualshive.com logo in svg

National Instruments PPC-2115, Руководство пользователя, Страница: 12 / 48

Поделиться
Скачать
National Instruments PPC-2115 Скачать руководство пользователя страница 12

Chapter 2

System Setup

©

 National Instruments Corporation

2-3

PPC-2115 User Manual

2.

Remove the dummy CompactFlash card from the slot in the 
PPC-2115. Install a CompactFlash card containing Windows CE, 
embedded Windows XP, or another operating system.

3.

Connect the power connector to 24 VDC power lines. Be sure 
to connect the positive, negative, and ground lines as shown in 
Figure 2-1. The power lines can be from either a power adapter or 
in-house power source.

Figure 2-1.  

Power Connector

4.

Connect the power connector to the power receptor on the PPC-2115. 
The power receptor pin assignment is shown in Figure 2-2.

Figure 2-2.  

Power Receptor and Pin Assignment

5.

Press the power button to power on the system.

Touchscreen Calibration

The PPC-2115 touchscreen should be correctly calibrated and ready to use 
when you power on the system. However, if the calibration is not correct or 
you want to choose custom calibration options, refer to Appendix F, 

Touchscreen Configuration

.

+

–

GND

GND

–

+

Содержание PPC-2115

















































Отзывы:

Нет отзывов