National Instruments PCI-6503 Скачать руководство пользователя | Manualshive

Страница: 58 / 88

background image

Appendix B

Register-Level Programming — Programming

©

National Instruments Corporation

B-17

PCI-DIO-96/PXI-6508/PCI-6503 User Manual

Programming Considerations for the 82C55A

Modes of Operation

The following list contains the three basic modes of operation for the 82C55A. Ports A and
B can operate in different modes.

•

Mode 0—Basic I/O—This mode is used for simple input and output operations for each
port. No handshaking is required; a specified port simply writes to or reads from data.
Mode 0 has the following features:

–

Two 8-bit ports (A and B) and two 4-bit ports (upper and lower nibbles of port C).

–

Any port can be input or output.

–

Outputs are latched, but inputs are not latched.

•

Mode 1—Strobed I/O—This mode transfers data that is synchronized by handshaking
signals. Ports A and B use the eight lines of port C to generate or receive the handshake
signals. This mode divides the ports into two groups (group A and group B) and includes
the following features:

–

Each group contains one 8-bit data port (port A or port B) and one 3-bit control/data
port (upper or lower portion of port C).

–

The 8-bit data ports can be either input or output; both are latched.

–

The 3-bit ports are used for control and status of the 8-bit data ports.

–

Interrupt generation and enable/disable functions are available.

•

Mode 2—Bidirectional bus—This mode is used for communication over a bidirectional
8-bit bus. Handshaking signals are used in a manner similar to mode 1. Mode 2 is
available for use in group A only (port A and the upper portion of port C). Other features
of this mode include the following:

–

One 8-bit bidirectional port (port A) and a 5-bit control/status port (port C).

–

Latched inputs and outputs.

–

Interrupt generation and enable/disable functions.

The 82C55A also has a single bit set/reset feature for port C, which is programmed by the
8-bit control word. Any of the eight bits of port C can be set or reset with one control word.
This feature generates control signals for port A and port B when these ports are operating in
mode 1 or mode 2.

«
...
56
57
58
59
60
...
»

Содержание PCI-6503

























































































Отзывы:

Нет отзывов

Похожие инструкции для PCI-6503

Бренд: ICP DAS USA Страницы: 48

Бренд: ICP DAS USA Страницы: 24

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: Garland Страницы: 6

Бренд: Pima Страницы: 4

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

Бренд: Neo Instruments Страницы: 2

ELITENAS EN104L+(B)

Бренд: Sans Digital Страницы: 9

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

J-Link-OB-STM32F072-128KB

Бренд: Segger Страницы: 18

CHEETAH ST34501FC

Бренд: Seagate Страницы: 68

Бренд: ZALMAN Страницы: 18

Бренд: Procool Страницы: 2

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

Бренд: ATTO Technology Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды