background image

8

|

ni.com

|

NI SCB-68 HSDIO Connection Guide & Specifications

Safety

This product meets the requirements of the following standards of safety for electrical equipment 
for measurement, control, and laboratory use:

IEC 61010-1, EN 61010-1

UL 61010-1, CSA 61010-1 

Note

For UL and other safety certifications, refer to the product label or the 

Online 

Product Certification

 section.

Electromagnetic Compatibility

This product meets the requirements of the following EMC standards for electrical equipment 
for measurement, control, and laboratory use:

EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity

EN 55011 (CISPR 11): Group 1, Class A emissions

AS/NZS CISPR 11: Group 1, Class A emissions

FCC 47 CFR Part 15B: Class A emissions

ICES-001: Class A emissions

Note

In the United States (per FCC 47 CFR), Class A equipment is intended for use 

in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, 
Australia and New Zealand (per CISPR 11) Class A equipment is intended for use 
only in heavy-industrial locations.

Note

Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical 

equipment that does not intentionally generate radio frequency energy for the 
treatment of material or inspection/analysis purposes.

Note

For EMC declarations and certifications, and additional information, refer to 

the 

Online Product Certification

 section.

CE Compliance

This product meets the essential requirements of applicable European Directives as follows:

2006/95/EC; Low-Voltage Directive (safety)

2004/108/EC; Electromagnetic Compatibility Directive (EMC)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance 
information. To obtain product certifications and the DoC for this product, visit 

ni.com/

certification

, search by model number or product line, and click the appropriate link in the 

Certification column.

Содержание NI SCB-68 HSDIO










Отзывы: