National Instruments NI sbRIO-961 Series Скачать руководство пользователя страница 47

Страница: 47 / 54

NI sbRIO-961x/9612XT/963x/9632XT/964x/9642XT

ni.com

Maximum total output current
on all channels ........................................20 A

Output impedance (

) ...........................0.3

max

Continuous overvoltage
protection range (V

sup

)............................40 V

Reversed-voltage protection ...................None

Current limiting ......................................None

Short-circuit protection...........................Indefinitely protected when a

channel is shorted to D GND or
to a voltage up to V

sup

Trip current for one channel

With all other channels
at 250 mA current............................3 A typ

With all other channels off ..............5 A typ

sup

quiescent current consumption .......28 mA max

Maximum update rate .............................40 µs max

Propagation delay ...................................500

s max

Power Limits

Caution

Exceeding the power limits may cause unpredictable behavior by the device.

5 V pins (P2, P3, P4, P5) ........................+5 V ±5%,

2 A max (shared with C Series
modules)

Power Requirements

The NI sbRIO device requires a power supply connected to connector J3.
Refer to Figure 4 for the location of J3. Refer to the

Powering the NI sbRIO

Device

section for information about connecting the power supply.

Power supply voltage range....................19–30 VDC

Power supply current limit .....................1.8 A

The NI sbRIO device is 1–2% more efficient with a 19 V supply than with a 30 V supply.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание NI sbRIO-961 Series























































Результаты поиска

Содержание NI sbRIO-961 Series

Отзывы:

Бренды по названию

Популярные бренды

National Instruments NI sbRIO-961 Series, Руководство пользователя

Результаты поиска

Содержание NI sbRIO-961 Series

Отзывы:

Бренды по названию

Популярные бренды