National Instruments NI PXIe-8105 Скачать руководство пользователя

Страница: 48 / 76

Chapter 3

I/O Information

NI PXIe-8105 User Manual

3-16

ni.com

Note

The pound symbol (#) indicates an active low signal.

Front Panel Features

The NI PXIe-8105 has the following front-panel features:

•

A system reset pushbutton (press the button to generate a reset to the
controller)

•

Two front panel LEDs that show PC status

–

The

POWER OK

LED indicates the power status of the

controller. The LED will indicate one of the following states:

•

ON steady—PXI and onboard power is on and within
regulation limits

•

BLINKING—One of the onboard power supplies is
operating outside of the normal limits

•

OFF—The controller is powered off

–

The

DRIVE

LED indicates when an access to the internal hard

disk is occurring.

Data Storage

The NI PXIe-8105 has the following data storage features:

•

Internal Serial ATA hard drive

–

60 GB minimum 2.5 in. notebook hard drive (30 GB minimum
PATA drive on Extended Temp Option controller)

–

Supports Native Command Queuing

–

Supports transfer rates up to 1.5 Gb/s

•

USB storage support—USB CD/DVD-ROM, mass storage device, or
floppy drive

Содержание NI PXIe-8105













































































Результаты поиска

Содержание NI PXIe-8105

Отзывы:

Похожие инструкции для NI PXIe-8105

Бренды по названию

Популярные бренды

National Instruments NI PXIe-8105, Руководство пользователя

Результаты поиска

Содержание NI PXIe-8105

Отзывы:

Похожие инструкции для NI PXIe-8105

Бренды по названию

Популярные бренды