National Instruments NI PXIe-8105 Скачать руководство пользователя | Manualshive

Страница: 32 / 76

background image

Chapter 2

Installation and Configuration

NI PXIe-8105 User Manual

2-18

ni.com

ExpressCard

This section provides information on the installation and removal of
ExpressCard modules.

Installing an ExpressCard

You can install an ExpressCard module while the NI PXIe-8105 is running.
The NI PXIe-8105 will automatically detect the card. ExpressCards are
generally marked with a symbol or a label to indicate which end to insert
into the slot. The cards are keyed to prevent incorrect insertion.

To install an ExpressCard, complete the following steps.

1.

Hold the card so the top side is facing left.

2.

Insert the card until it is completely seated in its connector. The
connector has an automatic eject mechanism. If you insert the card and
it is ejected, simply re-insert the card until it is seated.

If you encounter too much resistance, do not force the card. Check the card
orientation and try again.

The NI PXIe-8105 will automatically recognize the ExpressCard and load
the appropriate driver(s). Third-party cards may require that you install
additional drivers. Contact your ExpressCard vendor for more information.

Removing an ExpressCard

To remove the ExpressCard module push in the module and then release to
eject the card. Slide the card out of the slot.

Caution

To avoid data loss and other potential issues, stop communication with your

ExpressCard device before removing it from the NI PXIe-8105. In Windows, use the
Safely Remove Hardware tool to safely stop the ExpressCard.

«
...
30
31
32
33
34
...
»

Содержание NI PXIe-8105













































































Отзывы:

Нет отзывов

Похожие инструкции для NI PXIe-8105

Бренд: Barracuda Networks Страницы: 2

Бренд: 2N Страницы: 11

Бренд: 2N Страницы: 5

Бренд: 2N Telekomunikace Страницы: 24

Бренд: Abus Страницы: 60

Бренд: Patton electronics Страницы: 8

Бренд: Blackrock Microsystems Страницы: 27

Бренд: Commell Страницы: 9

Бренд: Garland Страницы: 43

Бренд: Dolphin Страницы: 9

Бренд: Comtrend Corporation Страницы: 4

Бренд: Bailey Страницы: 33

Mustang-M2AE-MX1

Бренд: IEI Technology Страницы: 58

Бренд: Alcatel-Lucent Страницы: 12

Бренд: Freescale Semiconductor Страницы: 124

Бренд: Promise Technology Страницы: 148

Бренд: HighPoint Страницы: 12

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды