National Instruments NI PXIe-5624 Скачать руководство пользователя

Страница: 20 / 21

NI PXIe-5624R Calibration Procedure

Call

niIFDig ExternalCal v1 Host.lvclass:Amplitude Cal

Initialize.vi

. Wire

External 10 MHz Reference Clock

to the

reference clock

source

input.

Call

niIFDig ExternalCal v1 Host.lvclass:Amplitude Cal

Configure.vi

Configure the signal generator using the following settings:

•

Frequency: value of the

frequency to generate (Hz)

output from

niIFDig

External Cal v1 Host.lvclass:Amplitude Cal Configure.vi

•

Power level: value of the

power to generate (dBm)

output from

niIFDig

External Cal v1 Host.lvclass:Amplitude Cal Configure.vi

plus

12 dB

•

Reference Clock source: Internal

10. Configure the power sensor to correct for the

frequency to generate (Hz)

output from

niIFDig External Cal v1 Host.lvclass:Amplitude Cal Configure.vi

using the power sensor frequency correction function.

11. Measure the power of the signal present at splitter output 1 of the power splitter using the

power sensor. Record this value as the

measured input power

12. Calculate the

corrected input power

using the following equation:

corrected input power

measured input power + splitter balance

Tip

Find the

splitter balance

by choosing the correct data point from the

Characterizing Power Splitter Balance

section. Remember that certain frequencies

are not measured due to harmonics aliasing back on the fundamental.

13. Call

niIFDig ExternalCal v1 Host.lvclass Amplitude Cal Adjust.vi

Wire the

corrected input power

calculated in step 12 to the

actual power (dBm)

input.

Wire the

frequency

output from

niIFDig External Cal v1 Host.lvclass:

Amplitude Cal Configure.vi

to the

actual frequency (Hz)

input.

14. Repeat steps 8 through 13 until the

amplitude calibration complete

output of

niIFDig

ExternalCal v1 Host.lvclass:Amplitude Cal Adjust.vi

returns a value of

TRUE.

15. Call

niIFDig ExternalCal v1 Host.lvclass:Close External

Calibration.vi

. Set the

write calibration to hardware?

input to TRUE to store the

results to the NI 5624R flash memory.

Содержание NI PXIe-5624






















Результаты поиска

Содержание NI PXIe-5624

Отзывы:

Похожие инструкции для NI PXIe-5624

Бренды по названию

Популярные бренды

National Instruments NI PXIe-5624, Процедура калибровки

Результаты поиска

Содержание NI PXIe-5624

Отзывы:

Похожие инструкции для NI PXIe-5624

Бренды по названию

Популярные бренды