National Instruments NI PXI-6541 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 40

National Instruments NI PXI-6541 Скачать руководство пользователя страница 37

36

|

ni.com

|

NI Digital Waveform Generator/Analyzer Getting Started Guide

I Received a Thermal or Power Shutdown Error

I received the

kErrorDeviceShutDownDueToHighTemp

or the

NIHSDIO_ERROR_DEVICE_POWER_LIMIT_EXCEEDED

error, and my device shut down.

What should I do next?

To re-enable your device after a hardware shutdown, you must perform a hard reset, in which
the device integrated circuits (ICs) are reloaded. To re-enable your device after thermal
shutdown, complete the following steps:
1.

Power off the computer or chassis that contains the device.

2.

Review the procedure in step

5. Installing the Hardware

and make any necessary

adjustments to ensure that your device is effectively cooled.

3.

Call the niHSDIO Reset Device VI or the

niHSDIO_ResetDevice

function or perform a

device reset in MAX. For more information about performing a device reset in MAX, refer
to step

6. Configuring and Testing in MAX

. The thermal shutdown error continues to be

reported until the device has been successfully reset.

Note

The thermal shutdown error is reported until the device has cooled to an

acceptable operating temperature and has been successfully reset.

Note

Due to power and cooling constraints, not all features of the NI 6555/6556

may be active at the same time. Refer to the

NI 6555/6556 Specifications

for power

limits and to the

NI 6555/6556

book in the

NI Digital Waveform Generator/Analyzer

Help

for more information about the power monitoring properties provided by

NI-HSDIO.

Performance Issues Using MXI Connection

When using a MXI connection to control the PXI chassis, the MXI Optimization Application
must be run prior to using the NI device. By default, this application runs automatically when
Windows starts. Use of a MXI connection without running this application may result in a time
exceeded or internal software error, or an initialization, timeout, or performance issue when
using the NI device.

If you are experiencing errors and are uncertain whether the MXI Optimization Application ran,
navigate to

Start»All Programs»National Instruments MXI

, and select

MXI Optimization

to launch the application.

If the application is not installed, refer to the software CD included with the MXI kit to install
the software. After installation, you may be required to reboot the computer before using the
MXI Optimization Application.

If you continue to have initialization or performance issues, refer to the MXI documentation at

Start»All Programs»National Instruments MXI

, or visit NI Technical Support at

ni.com/

support

.

«
...
35
36
37
38
39
...
»

Содержание NI PXI-6541









































Отзывы:

Нет отзывов