manualshive.com logo in svg

National Instruments NI PCIe-8255R, Руководство пользователя

Поделиться
Скачать
National Instruments NI PCIe-8255R Скачать руководство пользователя страница 17

Chapter 2

Hardware Overview

©

 National Instruments Corporation

2-5

NI PCIe-8255R User Manual

I/O for Normal Operation

The following sections describe I/O functions that are available on the 
NI 8255R during normal operation.

Trigger Inputs

Trigger inputs are available from both TTL inputs and isolated inputs. You 
can use these trigger inputs to synchronize the NI 8255R with an external 
event, such as the assertion of a signal generated by a proximity sensor or 
a PLC, to indicate that an inspection item is passing in front of the camera. 
The NI 8255R can use this input to initiate a timed pulse for camera control, 
lighting control, encoder pulse counting, and result output timing.

For more information about creating a timed pulse output, refer to the 

Timed Pulse Output

 section.

TTL Input 0, TTL Input 1, TRIG 0, ISO Input 6, ISO Input 7, ISO Input 8, 
and ISO Input 11 can alternatively function as general-purpose inputs. 
ISO Input 5 can alternatively function as a latch for the product selection 
port.

Timed Pulse Output

The NI 8255R is capable of timed pulse output on six different digital 
outputs, which provides precise control over time-critical signals, such as 
camera exposure. This section describes the various uses for the timed 
pulse output and the parameters you can set to control these outputs.

Uses for timed pulse output include controlling camera reset and exposure, 
controlling strobe lighting, operating plungers on an assembly line, and 
communicating with PLCs. You can configure the start of the pulse output 
generation to occur from software or from a rising or falling edge of a 
trigger input.

In addition to controlling the timing of pulse output, you can also configure 
the polarity of the output signal, resulting in a high-true or low-true signal. 
Based on the polarity setting, the output signal asserts after the appropriate 
delay time and de-asserts after the configured pulse width. You can set the 
delay time in microseconds or in quadrature encoder counts from the start 
signal—either a hardware trigger or a software command. Width is always 
configured in microseconds.

Содержание NI PCIe-8255R














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды