background image

©

 National Instruments Corporation

9

Getting Started with the NI EVS-1463

CE Compliance

This product meets the essential requirements of applicable European Directives as follows:

2006/95/EC; Low-Voltage Directive (safety)

2004/108/EC; Electromagnetic Compatibility Directive (EMC)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance 
information. To obtain product certifications and the DoC for this product, visit 

ni.com

/

certification

, search by model number or product line, and click the appropriate link in the 

Certification column.

Environmental Management

National Instruments is committed to designing and manufacturing products in an environmentally 
responsible manner. NI recognizes that eliminating certain hazardous substances from our products is 
beneficial not only to the environment but also to NI customers.

For additional environmental information, refer to the 

NI and the Environment

 Web page at 

ni.com/

environment

. This page contains the environmental regulations and directives with which NI 

complies, as well as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of the product life cycle, all products 

must

 be sent to a WEEE recycling 

center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, 
and compliance with WEEE Directive 2002/96/EC on Waste and Electronic Equipment, visit 

ni.com/environment/weee

.

Battery Replacement and Disposal

Battery Directive

This device contains a long-life coin cell battery. If you need to replace it, use the 

Return Material Authorization (RMA) process or contact an authorized National Instruments service 
representative. For more information about compliance with the EU Battery Directive 2006/66/EC 
about Batteries and Accumulators and Waste Batteries and Accumulators, visit 

ni.com/

environment/batterydirective

.

Cd/Hg/Pb

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 (RoHS)

DŽ

݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/environment/rohs_china

DŽ

(For information about China RoHS compliance, go to 

ni.com/environment/rohs_china

.)

Содержание NI EVS-1463













Отзывы: