National Instruments NI cDAQTM-9138 Скачать руководство пользователя | Manualshive

Страница: 122 / 141

background image

© National Instruments

|

A-5

NI cDAQ-9138/9139 User Manual

•

Serial Port Configuration

—Use this setting to access the

Serial Port Configuration

submenu. Refer to the

Serial Port Configuration Submenu

section for more information.

•

Serial Port Console Redirection

—Use this setting to access the

Serial Port Console

Redirection

submenu. Refer to the

Serial Port Console Redirection Submenu

section for

more information.

SATA Configuration Submenu

Use this submenu to apply alternate settings to the hard disk drive (HDD) interfaces. Normally,
you do not need to modify these settings, as the factory default settings provide the most
compatible and optimal configuration possible.
•

SATA Mode Selection

—This setting determines whether AHCI mode is enabled or

disabled for the SATA port. Some operating systems, do not support AHCI mode. You can
use this setting to disable AHCI mode and enable IDE mode so that non-compatible OSes
function correctly. The default value is AHCI.

•

Onboard Storage

—This item displays the onboard drive detected in the system.

CPU Configuration Submenu

Use this submenu to apply alternate settings to the CPU. Normally, you do not need to modify
these settings, as the factory default settings provide the most compatible and optimal
configuration possible.
•

Hyper-Threading

—

(NI cDAQ-9139)

This setting enables or disables Intel

Hyper-Threading technology. The default value is

Disabled

if the boot OS is

LabVIEW Real-Time and

Enabled

for other boot OSes. Enabling Hyper-Threading

increases performance for some applications by adding virtual CPU cores.
Hyper-Threading can cause control algorithms to behave less deterministically.

•

Enabled CPU Cores

—This setting selects the number of active CPU cores for the

processor. Valid values are 2 and 1. The default value is

2

.

•

Turbo Boost—

(NI cDAQ-9139)

This setting enables or disables Intel Turbo Boost

technology. The default value is

Disabled

if the boot OS is LabVIEW Real-Time and

Enabled

for other boot OSes. Enabling Turbo Boost allows CPU cores to run at higher than

their base frequency for short durations, while other cores are idle. Enabling Turbo Boost
can cause control algorithms to behave less deterministically.

•

Hardware Prefetcher

—This setting enables or disables CPU cache hardware prefetching.

The default value is enabled.

•

Adjacent Cache Line Prefetch

—This setting enables or disables prefetching of adjacent

cache lines from memory to the CPU cache. The default value is enabled.

«
...
120
121
122
123
124
...
»

Содержание NI cDAQTM-9138














































































































































Отзывы:

Нет отзывов

Похожие инструкции для NI cDAQTM-9138

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: E+E Elektronik Страницы: 20

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренд: V2 Страницы: 124

Бренд: Parker Страницы: 4

Бренд: Lab.gruppen Страницы: 2

Бренд: Mitsubishi Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды