background image

© 

National Instruments Corp.

37

NI 9512 Operating Instructions and Specifications

Where to Go for Support

The National Instr

u

ments Web site is yo

u

r complete reso

u

rce for 

technical s

u

pport. At 

ni.com/

s

upport

 yo

u

 have access to 

everything from tro

u

bleshooting and application development 

self-help reso

u

rces to email and phone assistance from 

NI Application Engineers.

National Instr

u

ments corporate headq

u

arters is located at 

11500 North Mopac Expressway, A

u

stin, Texas, 78759-3504. 

National Instr

u

ments also has offices located aro

u

nd the world to 

help address yo

u

r s

u

pport needs. For telephone s

u

pport in the 

United States, create yo

u

r service req

u

est at 

ni.com/

s

upport

 

and follow the calling instr

u

ctions or dial 512 795 8248. For 

telephone s

u

pport o

u

tside the United States, contact yo

u

r local 

branch office: 

A

u

stralia 1800 300 800, A

u

stria 43 662 457990-0, 

Belgi

u

m 32 (0) 2 757 0020, Brazil 55 11 3262 3599, 

Canada 800 433 3488, China 86 21 5050 9800, 
Czech Rep

u

blic 420 224 235 774, Denmark 45 45 76 26 00, 

Finland 358 (0) 9 725 72511, France 01 57 66 24 24, 
Germany 49 89 7413130, India 91 80 41190000, 
Israel 972 3 6393737, Italy 39 02 41309277, Japan 0120-527196, 

Содержание NI 9512








































Отзывы: