National Instruments NI 9222 Скачать руководство пользователя страница 2

Страница: 2 / 27

NI 9222/9223

ni.com

This doc

ment describes how to

se the National Instr

ments 9222

and National Instr

ments 9223 and incl

des specifications and

terminal assignments for the NI 9222 and NI 9223. In this
doc

ment, the NI 9222 and NI 9223 are referred to incl

sively as

the NI 9222/9223.Visit

ni.com/info

and enter

oftwarever

ion

to determine which software yo

need for

the mod

les yo

are

sing. For information abo

t installing,

config

ring, and programming the system, refer to the system

doc

mentation. Visit

ni.com/info

and enter

erie

doc

for

information abo

t C Series doc

mentation. Visit

ni.com/info

and enter

compatibility

for information abo

t chassis and

carrier compatibility for the mod

les yo

are

sing.

Note

The safety g

idelines and specifications in this

doc

ment are specific to the NI 9222/9223. The other

components in the system might not meet the same safety
ratings and specifications. Refer to the doc

mentation for

each component in the system to determine the safety
ratings and specifications for the entire system. Visit

ni.com/info

and enter

erie

doc

for information

abo

t C Series doc

mentation.

Содержание NI 9222




























Результаты поиска

Содержание NI 9222

Отзывы:

Похожие инструкции для NI 9222

Бренды по названию

Популярные бренды

National Instruments NI 9222, Инструкция по эксплуатации и технические характеристики

Результаты поиска

Содержание NI 9222

Отзывы:

Похожие инструкции для NI 9222

Бренды по названию

Популярные бренды