National Instruments MXI-Express x1 Series Скачать руководство пользователя | Manualshive

Страница: 35 / 120

background image

3-8

|

ni.com

Chapter 3

Installation and Configuration

5.

Hold the handle as you slowly slide the module into the chassis until the handle catches on
the injector/ejector rail.

6.

Raise the injector/ejector handle until the module firmly seats into the backplane receptacle
connectors. The front panel of the NI PXI board should be even with the front panel of the
chassis.

7.

Tighten the bracket-retaining screws on the top and bottom of the front panel to secure the
NI PXI board to the chassis.

8.

Replace or close any doors or covers to the chassis.

Note

Figure 3-7 shows an NI PXI board and chassis installation. The same

procedure applies for a PXI Express board and chassis.

Cabling

MXI-Express x1 products support two types of cable of various lengths. Table 3-2 and 3-3 list
the MXI-Express x1 cables available from National Instruments.

Powering On the MXI-Express x1 System

1.

Power on all of the expansion chassis in any order you choose.

2.

Power on the host.

Note

There are no requirements on the order that connected expansion chassis are

powered up relative to each other, as long as they are all on before the computer is
powered on.

Table 3-2.

National Instruments MXI-Express x1 Copper Cables

Cable Length (Meters)

Description

Part Number

1 m

MXI-Express x1 copper cable

779500-01

3 m

MXI-Express x1 copper cable

779500-03

7 m

MXI-Express x1 copper cable

779500-07

Table 3-3.

National Instruments MXI-Express x1 Fiber Cables

Cable Length (Meters)

Description

Part Number

10 m

MXI-Express x1 fiber cable

778959-10

30 m

MXI-Express x1 fiber cable

778959-30

200 m

MXI-Express x1 fiber cable

778959-200

«
...
33
34
35
36
37
...
»

Содержание MXI-Express x1 Series

























































































































Отзывы:

Нет отзывов

Похожие инструкции для MXI-Express x1 Series

Бренд: Ecco Страницы: 3

Бренд: GE Страницы: 698

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: ICP DAS USA Страницы: 45

Бренд: K-9 Lights Страницы: 12

Chandler Engineering 1910

Бренд: Ametek Страницы: 46

Бренд: ORORO Страницы: 16

Бренд: Karma Страницы: 12

Бренд: p-light Страницы: 28

Бренд: Cardin Elettronica Страницы: 56

Бренд: North Light Страницы: 5

Бренд: Nexus Страницы: 79

Бренд: Teletek electronics Страницы: 2

Бренд: Hameg Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды