National Instruments GPIB-MAC Скачать руководство пользователя | Manualshive

Страница: 42 / 142

background image

November 1985

National Instruments

caddr

Syntax:

Purpose:

Remarks:

Change GPIB Address of the GPIB-MAC

Initialization function

You use caddr at the beginning of your program to
change the GPIB address of the GPIB-MAC.

The argument addr is a device address that specifies the
new GPIB address for the GPIB-MAC. addr consists
of a primary address and an optional secondary address.
The secondary address is separated from the primary

address by a plus sign

Both addresses are

expressed as numeric strings.

Only the lower five bits of each address are significant.
These bits may be in the range from 0 through 30 for
both the primary and the secondary address. Therefore,
the binary value 01100010 (decimal 98) is interpreted as
decimal 2.

The following examples all specify a primary address of
0 and a secondary address of 2. The listen address is
32, the talk address is 64, and the secondary address is 2
or 98, which are equivalent.

or

or

or

If you specify a primary address without a secondary
address, secondary addressing is disabled.

If you call caddr without an argument, the GPIB-MAC
returns to you its current GPIB address.

The address assigned by this function remains in effect
until you call caddr again, call onl, or you turn off the
GPIB -MAC.

31

SECTION FOUR FUNCTIONS

«
...
40
41
42
43
44
...
»

Содержание GPIB-MAC















































































































































Отзывы:

Нет отзывов

Похожие инструкции для GPIB-MAC

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Бренд: MADRIX Страницы: 12

Бренд: Narcotrend Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды