National Instruments FIELDPOINT CFP-CB-1 Скачать руководство пользователя

Страница: 1 / 20

FIELDPOINT

™

OPERATING INSTRUCTIONS

AND SPECIFICATIONS

cFP-CB-1/2/3/4

Compact FieldPoint Connector Blocks

These operating instructions describe how to install and use the
cFP-CB-1, cFP-CB-2, cFP-CB-3, and cFP-CB-4 (referred to
inclusively in this manual as the cFP-CB-

Features

The cFP-CB-

Compact FieldPoint connector blocks have the

following features:

•

Designed for general-purpose and hazardous-voltage
operation with all Compact FieldPoint I/O modules (cFP-CB-1
and cFP-CB-2)

•

Isothermal construction minimizes temperature gradients for
use with thermocouples (cFP-CB-3)

•

Mounting on a cFP-BP-

or cFP-180

Compact FieldPoint

backplane

•

Up to 36 terminals

•

Tie-wrap anchors for wires (cFP-CB-1 and cFP-CB-3)

•

Front-panel access to terminals (cFP-CB-2 and cFP-CB-4)

•

Removable front-mounted connectors (cFP-CB-2 and
cFP-CB-4)

•

Spring terminals or screw terminals available

•

V and C terminals for voltage supply and common connections

•

–40 to 70 °C operation

Содержание FIELDPOINT CFP-CB-1





















Результаты поиска

Содержание FIELDPOINT CFP-CB-1

Отзывы:

Похожие инструкции для FIELDPOINT CFP-CB-1

Бренды по названию

Популярные бренды

National Instruments FIELDPOINT CFP-CB-1, Руководство по эксплуатации

Результаты поиска

Содержание FIELDPOINT CFP-CB-1

Отзывы:

Похожие инструкции для FIELDPOINT CFP-CB-1

Бренды по названию

Популярные бренды