manualshive.com logo in svg
background image

© 

National Instruments Corp.

19

cFP-CB-1/2/3/4

Environmental Management

NI is committed to designing and manufacturing products in 
an environmentally responsible manner. NI recognizes that 
eliminating certain hazardous substances from our products is 
beneficial not only to the environment but also to NI customers.

For additional environmental information, refer to the 

NI and the 

Environment

 Web page at 

ni.com/environment

. This page 

contains the environmental regulations and directives with which 
NI complies, as well as other environmental information not 
included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of their life cycle, all products 

must

 be sent to a WEEE recycling center. For more 

information about WEEE recycling centers and 
National Instruments WEEE initiatives, visit 

ni.com/environment/weee

.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃ

ѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 (RoHS)

DŽ݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/environment/rohs_china

DŽ

(For information 

about China RoHS compliance, go to 

ni.com/

environment/rohs_china

.)

Содержание FIELDPOINT CFP-CB-1





















Отзывы: