manualshive.com logo in svg

National Instruments FieldPoint cFP-AI-100, Руководство по эксплуатации

Поделиться
Скачать
National Instruments FieldPoint cFP-AI-100 Скачать руководство пользователя страница 9

FP-AI-100 and cFP-AI-100

8

ni.com

Input Ranges

To prevent inaccurate readings, choose an input range such that the 
signal you are measuring does not exceed either end of the range. 
If a channel is not in use, short the positive input to ground and 
configure the channel for a bipolar input range. Small fluctuations 
in floating input signals can cause the red 

Out of Range

 status 

LED on the module to light if the channel is configured for a 
unipolar range. Similarly, if a channel is configured for 4–25 mA 
input and the input current is 0 mA, the channel is always out of 
range.

Overranging

The [c]FP-AI-100 has an overranging feature that measures a little 
beyond the nominal values of each range. For example, the actual 
measurement limit of the 

±

5 V range is 

±

6.0 V. The overranging 

feature allows the [c]FP-AI-100 to compensate for field devices 
with span errors of up to +20% of full scale. Also, with the 
overranging feature, a noisy signal near full scale does not create 
rectification errors.

Status Indicators

The [c]FP-AI-100 has two green status LEDs, 

POWER

 and 

READY

. After you insert the [c]FP-AI-100 into a terminal base 

or backplane and apply power to the connected network module, 
the green 

POWER

 indicator lights and the [c]FP-AI-100 informs 

the network module of its presence. When the network module 
recognizes the [c]FP-AI-100, it sends initial configuration 
information to the [c]FP-AI-100. After the [c]FP-AI-100 receives 
this initial information, the green 

READY

 indicator lights and the 

module is in normal operating mode.

In addition to the green 

POWER

 and 

READY

 indicators, the 

[c]FP-AI-100 has one red status LED that lights when the input 
signal on any channel is outside the configured range. Refer to the 

Input Ranges

 section for information about selecting input ranges.

Upgrading the FieldPoint Firmware

You may need to upgrade the FieldPoint firmware when you add 
new I/O modules to the FieldPoint system. For information on 
determining which firmware you need and how to upgrade the 
firmware, go to 

ni.com/info

 and enter 

fpmatrix

.

Содержание FieldPoint cFP-AI-100


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды