background image

cRIO-9073, cRIO-9074

FPGA type

Xilinx Spartan-3 2M

Number of flip-flops

40,960

Number of 4-input LUTs

40,960

Number of multipliers

40

Available block RAM

720 kbits

Number of DMA channels

3

For information about the life span of the nonvolatile memory and about best practices for
using nonvolatile memory, go to 

ni.com/info

 and enter the Info Code 

SSDBP

.

Internal Real-Time Clock

Accuracy

200 ppm; 35 ppm at 25 °C

Power Requirements

Caution

 

You must use a UL Listed ITE power supply marked 

LPS

 with the

cRIO-9072/9073/9074.

Recommended power supply

48 W, 24 VDC

Power consumption

20 W maximum

Power supply input range

19 V to 30 V

Physical Characteristics

If you need to clean the module, wipe it with a dry towel.

Tip

 

For two-dimensional drawings and three-dimensional models of the C Series

module and connectors, visit 

ni.com/dimensions

 and search by module number.

Screw-terminal wiring

Gauge

0.13 mm 

2

 to 2.1 mm

2

 (26 AWG to 14 AWG)

copper conductor wire

Wire strip length

6 mm (0.24 in.) of insulation stripped from the
end

Temperature rating

85 °C

Torque for screw terminals

0.20 N · m to 0.25 N · m (1.8 lb · in. to
2.2 lb · in.)

Wires per screw terminal

One wire per screw terminal

Ferrules

0.25 mm

2

 to 1.5 mm

2

20

  | 

ni.com

  | 

NI cRIO-9072/9073/9074 User Manual and Specifications

Содержание CompactRIO cRIO-9072



























Отзывы: