National Instruments Compact FieldPoint cFP-21 Series Скачать руководство пользователя

Страница: 64 / 74

Appendix B

Specifications

B-4

ni.com

Safety

This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control, and
laboratory use:

•

IEC 61010-1, EN 61010-1

•

UL 61010-1

•

CAN/CSA-C22.2 No. 61010-1

Note

For UL and other safety certifications, refer to the product label, or visit

ni.com/certification

, search by model number or product line, and click the

appropriate link in the Certification column.

Electromagnetic Compatibility

Emissions................................................EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity ................................................EN 61326:1997 + A2:2001,

Table 1 (Industrial Levels)

CE, C-Tick, and FCC Part 15 (Class A) Compliant

Note

For EMC compliance, operate this device with shielded cabling.

CE Compliance

This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:

Low-Voltage Directive (safety)..............73/23/EEC

Electromagnetic Compatibility
Directive (EMC) .....................................89/336/EEC

Note

Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit

ni.com/certification

, search by model number or product line, and click the

appropriate link in the Certification column.

Содержание Compact FieldPoint cFP-21 Series











































































Результаты поиска

Содержание Compact FieldPoint cFP-21 Series

Отзывы:

Похожие инструкции для Compact FieldPoint cFP-21 Series

Бренды по названию

Популярные бренды

National Instruments Compact FieldPoint cFP-21 Series, Руководство пользователя

Результаты поиска

Содержание Compact FieldPoint cFP-21 Series

Отзывы:

Похожие инструкции для Compact FieldPoint cFP-21 Series

Бренды по названию

Популярные бренды