Error
No picture seen
Screen module crash
(photo storage ceased,
no input reactions, switch off
impossible)
Memory card does not function
(512 MB and higher)
Need Help? Toll Free 866-252-3811
5.3.4 Feeding your saltwater prawns
To keep them alive saltwater prawns must be fed occasionally. This must
be done carefully as overfeeding causes the water to stagnate and poison
the prawns. Feeding is best down with dry powdered yeast (Fig 5.37
A). Give them a little every other day. If the water darkens this signifies
it is stagnating. If so remove the prawns and put them in a fresh saline
solution.
Note:
Shrimp eggs and shrimps are not suitable for consumption!
6. Image output and storage (SD card required)
The LCD Micro has the option to display pictures and store them:
a) View the picture on the LCD screen (sections 1+2.2).
b) You can store your photographs on a suitable sd memory card (SD =
Secu-
re Digital). The memory card slot of the LCD Micro is on the left hand
side of the screen module (Fig. 1+2.1) above the USB connection. To use,
push the memory card, with the contacts at the front, into the slot, until
they engage with a faint click. If the installation is correct, a blue memory
card symbol appears above on the LCD monitor. This is again released by
pressing and releasing the memory card, which after a faint click, can be
taken out of the slot. Your photographs are now transportable.
c) If you connect your microscope to the PC using the USB cable
provided (Fig. 5.32), you can transfer the photographs to the PC. The
SD-Memory card has
to be plugged in. The USB connection of the LCD Micro is on the left
side of
the screen module (Fig. 1+2.1) under the memory card slot. Put the
smaller B- plug (Micro) into the socket on the microscope and the larger
A plug (PC) into a free USB port in your computer (Fig. 5.32). After a
successful USB connection, the operating system will recognize new
hardware and then a new drive will be initialized. This drive is marked as
“removable data carrier e“ or “removable data carrier f:“, the letters vary
depending upon the number of drive assemblies in your computer. They
are made available on the work station, as well as in Windows Explorer.
This drive contains the contents of your sd-memory card.
Note:
1. The “Access SD card error!“ after removing the card is to be acknowl-
edged by pressing OK.
2. If the card contains a lot of data the microscope module may be very
slow or not react (Crash). Please then remove the card, turn the power to
the microscope off, wait a bit and then start again.
3. If you delete a lot of data using DelFile / All this may not work first
time round. If so simply repeat it until it does.
Caution:
When taking a photograph, no USB connection between PC and micro-
scope may exist. Before you interrupt the USB connection or switch the
screen module off, you must „deactivate“ the sd-card drive with the help
of the hardware assistant (removable data carrier) ! If the drive is not
deactivated, the PC might “crash“ or there might even be a loss of data!
Note:
We recommend the use of SD-memory cards (Secure Digital) with 1 GB
or up to 8 GB of storage capacity.
7. Care and maintenance
The microscope is a high quality optical appliance. Therefore you should
make sure that dust or moisture do not come into contact with your mi-
croscope. Avoid putting fingerprints on any optical surfaces.
If dust or dirt should nevertheless have gotten onto your microscope, or
the accessories, you should first remove this with a soft brush.
Then clean the soiled area with a soft, lint-free cloth. To remove finger
-
prints from the optical surfaces it is best to use a lint-free, soft cloth, to
which you have applied some alcohol.
After usage, you should stow the microscope and the accessories in their
correct containers again.
Remember:
A well maintained microscope will keep its optical quality for years and
thus maintain its value.
8. Elimination of errors
9. Technical data
System requirements for USB connection/memory card use:
Windows operating system
Main board with USB connection
Media program (e.g. image processing program, program for playing
films)
SD Memory card (not included) up to 32 GB max. (8 GB card recom-
mended).
SD Memory card reader
Your dealer.
Name:
Postcode/City:
Street:
Telephone:
Date of purchase:
Signature:
Solution
switch on Light
switch on LCD monitor
re-set the focus
Remove card and mains plug, wait
reinsert it and then turn the LCD
screen on.
Use a memory card with smaller
capacity