NatComm DS3 Скачать руководство пользователя страница 7

Страница: 7 / 28

Natcomm

Page 7

DIAL OUT OPERATION

If your site is unattended,

DS3

can DIAL OUT and CONNECT THE DOOR PHONE

CALL to a Pre-Programmed Telephone Number or a Mobile Telephone number (See
Pages 25-26 for Programming Details).

It can do so Immediately, or only if the Door Phone call has not been answered internally
by a preset number of rings.

Dial Out Immediately (Press #1), Dial Out after Ring Count (Press #2)          and Disable
Dial Out  (Press #3) are all set via Touch Tone commands from ANY Telephone on your
line, at any time (except  in Programming Mode).

To set ‘Unattended Mode’

(Dials out immediately)

Pick up any telephone, press

and then hang up.

(you will hear 1 ‘beep’ to confirm setting)

In this mode

DS3

will

DIAL OUT to the Programmed Number

as soon as the Door

Phone is triggered by your visitor call.

To set ‘Attended Mode’

(Only Dials out after ring count)

Pick up any telephone, press

and then hang up.

(you will hear 2 ‘beeps’ to confirm setting)

In this mode

DS3

will only

DIAL OUT to the Programmed Number

if the Door Phone

call is

not answered

before the preprogrammed ring count.

To set ‘Disable Dial Out’

(will not Dial Out)

Pick up any telephone, press

and then hang up.

(you will hear 3 ‘beeps’ to confirm setting)

This Mode will totally DISABLE the DIAL OUT facility:

Note - Your DS3 is set by DEFAULT to ‘Disable Dial Out’, to ENABLE DIAL OUT,
you MUST press #1 or #2 as appropriate.

Содержание DS3





























Результаты поиска

Содержание DS3

Отзывы:

Похожие инструкции для DS3

Бренды по названию

Популярные бренды

NatComm DS3, Руководство пользователя

Результаты поиска

Содержание DS3

Отзывы:

Похожие инструкции для DS3

Бренды по названию

Популярные бренды