manualshive.com logo in svg

Nastec VASCO, Руководство по эксплуатации

Поделиться
Скачать
Nastec VASCO Скачать руководство пользователя страница 30

 

30 
 

Slave setup  

Follow Master setup until point 11.  

In case of failure of master in a Combo system, will be replaced by slave. As a consequence, all parameters must be setup 
independently on each inverter, master mode. 

1.

 

Set: 

 

VASCO’s address in parallel operation.  

 

01 --> 07: VASCO slaves 

2.

 

Press STOP (red button). 

3.

 

In the 

advanced parameters

 verify that 

Autorestart

 is set 

ON.

 

4.

 

Press STOP (red button). 

5.

 

Press STOP again. 

Whenever the user accesses the Menu screen of the VASCO master, the communication between VASCOs is automatically 
interrupted.  
 
In case of alarm or failure of a pump in a Combo system, this pump’s operation will be replaced (temporary or 
permanently) by another pump. 

In case of failure of master in a Combo system, it will be replaced by the next slave. As a consequence of this, all 
parameters must be setup independently on each inverter as master mode. 

10. Trouble-shooting chart 

 

LCD does not switch on after powering 
the VASCO 

 

Check the connecting flat cable between the LCD board (attached to the 
cover) and the control board  

 

Check the fuses 

 

Check that the power cables are properly connected. 

Power line of VASCO is interrupted by 
the differential protection contactor 

 

Check the leakage current to ground of EMC filter   

 

Following a rapid off/on the power supply, the differential contactor can 
interrupt the power.  After turning off the VASCO it is recommended to 
wait at least 1 minute before restarting. 

When performing the Offset operation 
of the pressure device, SENS.PRESS.OFF 
alarm occurs   

 

Check that the sensor cable is properly connected to the sensor device 
and to the VASCO. 

 

Make sure that the sensor and its cable are not damaged. 

 

Check that the operating range of pressure sensor  is of  4 -20 mA type 
and the value of 15 V is within the voltage feed range of the sensor 

Frequency and pressure oscillation on 
constant pressure control mode 

 

Check if the water tank and its air pressure are correctly set.  It may be 
necessary to increase the tank volume or reduce the pre-charge 
pressure. 

 

Check the ki & kp parameters (Installer Parameters menu). At first, it is 
suggestable to increase the Ki value. If it not enough reduce of one unit 
the Kp value. 

During constant pressure control, pump 
stops and starts continuously. 

 

Make sure that the value f min Q=0 (minimum frequency with Q=0) 
(Installer Parameters menu) is properly set up. Otherwise repeat the 
procedure. 

 

Increase the value of  parameter  stop delay  (Installer Parameter menu) 

Address 

XX 

Содержание VASCO



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды