manualshive.com logo in svg

Nasco Lifeform LF01121U, Инструкция по эксплуатации

Поделиться
Скачать
Nasco Lifeform LF01121U Скачать руководство пользователя страница 5

4.

  With the other shoulder tube attached to the second (empty) fluid  

   supply bag B, 

(see Figure 4)

 gradually “flush” the vascular system  

   with synthetic blood by slowly opening the clamp on fluid supply  

   bag A. 

(See Figure 5.) 

(The pinch clamp on fluid supply bag B  

   should be open.)

 

Allow same “blood” to pass through the system  

   until the air bubbles have been eliminated.

5.

  Close the clamp on bag A and then turn the arm over so it is palm  

   up. Slowly open the clamp on bag A to allow some blood to pass  

   through and to remove any remaining air that is trapped in the 

   system. 

(See Figure 6.)

  

Note:

 It may be necessary to swap the positions of the fluid supply  

   bags A and B during the filling process in order to prevent bubbles in  

   the tubing. If bag A runs out of blood before the arm is fully prepped,  

   simply remove it from its hanging position and replace it with (full)  

   bag B.

6.

  Once the system is filled, close the clamp on (resting) fluid supply  

   bag B and leave (hanging) fluid supply bag A clamp open. The arm 

   is now fully pressurized and can be used palm up or down.

4.

  With the other shoulder tube attached to the second (empty) fluid  

   supply bag B, 

(see Figure 4)

 gradually “flush” the vascular system  

   with synthetic blood by slowly opening the clamp on fluid supply  

   bag A. 

(See Figure 5.) 

(The pinch clamp on fluid supply bag B  

   should be open.)

 

Allow same “blood” to pass through the system  

   until the air bubbles have been eliminated.

5.

  Close the clamp on bag A and then turn the arm over so it is palm  

   up. Slowly open the clamp on bag A to allow some blood to pass  

   through and to remove any remaining air that is trapped in the 

   system. 

(See Figure 6.)

  

Note:

 It may be necessary to swap the positions of the fluid supply  

   bags A and B during the filling process in order to prevent bubbles in  

   the tubing. If bag A runs out of blood before the arm is fully prepped,  

   simply remove it from its hanging position and replace it with (full)  

   bag B.

6.

  Once the system is filled, close the clamp on (resting) fluid supply  

   bag B and leave (hanging) fluid supply bag A clamp open. The arm 

   is now fully pressurized and can be used palm up or down.

Figure 4

Figure 4

Figure 5

Figure 5

Figure 6

Figure 6

5

5

NP097_95_LF01121U_LF01126U_AdvancedInjectionArm.indd   5

12/19/14   3:29 PM

Содержание Lifeform LF01121U













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды